DIYTowing dolly instructions.pdf

Hookup of the Tow Dolly to Truck

1. The coupler locking device must be in the full open position. If equipped with a lower locking

plate, the plate must be in the down position. Place the coupler of the tow dolly over the 2"

hitch ball on the truck. Be sure the coupler is fully seated down over the ball.

Lever-Type Coupler

(with locking plate)

Handwheel-Type Coupler

2. Completely lock the coupler. If equipped with a level-type coupler,the lever must be in the

down position and the locking pin inserted. If equipped with a handwheel-type coupler,

completely tighten the handwheel.Pull up on the tow dolly tongue to be sure it is properly

secured.

3. Connect the color-coded wires from the tow dolly to the

corresponding color-coded posts on the truck's electrical box. Check for

proper operation.

4. Crisscross the safety chains from the tongue of the tow dolly. Pass through eyelets on truck

and attach hook to safety chain. Allow slack in the chains for movement during turns made by

the truck and tow dolly.

Hookup of the Towed Vehicle to Tow Dolly

It is the customer's responsibility to hook up the towed vehicle to the tow dolly. Consult your

insurance carrier before towing as Penske is not responsible for any damage to a towed vehicle.

1. Be sure that the truck and tow dolly are straight and on level ground.

2. Make sure that the tow dolly platform is straight.

3. Remove safety pin on ratchet assembly and unroll tire

straps.

4. Lay tire straps along fender side of tow dolly, off of tire platform.

5. Allow tow dolly platform to tilt back by releasing the locking pin.

6. Slowly drive the front end of the towed vehicle onto the tow dolly until tires on the towed

vehicle are resting against the tow dolly wheel stops. The platform will go into upright

position.Make certain that the towed vehicle is centered on the tow dolly platform since the

platform swivels during turns. Adequate space is required between the tow dolly fenders and

towed vehicle.Never back up a towed vehicle onto a tow dolly.

7. Locking pin on platform must go into the locked position.

8. For safety reasons, engage the parking brake on the towed vehicle (see item #13) and place

transmission in low gear (standard) or park (automatic).

9. Center the tie-down ratchets in front of the towed vehicle's tires and pull the tire straps

forward over the tires.

10. Tighten each tire strap securely by pulling up and down as many times as necessary on the

tow dolly ratchet assembly handle. Be sure the strap on the inside of the tire does not come in

contact with any brake or suspension parts. Insert safety pins and attach safety clip with

handle in down position.

11. Hook up safety chains from tow

dolly platform to the frame of towed

vehicle directly above the area where

chains are mounted on the tow dolly.

Allow slight slack in the chains to

provide for suspension movement on

the towed vehicle.

12. Disconnect the drive shaft on the

towed vehicle if rear-wheel or four-wheel

drive. Consult your dealer if you are

uncertain of the above. Towing above

vehicle without disconnecting drive shaft

will damage towed vehicle's transmission

even if transmission is placed in neutral.

13. Release parking brake on towed vehicle and be sure the steering is locked in the straight

position.

14. Remove keys from ignition and lock vehicle.

15. Check the towing system after hookup, tow about 100 feet, then stop and perform a safety

check. Check the bolts, chains, coupler, ramps, tire straps, and other items to make sure they

are in the right position and secure.

16. Repeat the safety check after the first five miles and then every 50 miles thereafter.

Towed vehicle is now safely connected and ready to be towed.

CHECK THE TOW DOLLY BOLTS, COUPLER, SAFETY CHAINS, ELECTRICAL HOOKUP,

AND TIRE STRAPS AFTER THE FIRST FIVE MILES OF TRAVEL AND THEN EVERY 50

MILES THEREAFTER.

Unload Towed Vehicle from Tow Dolly

1. Park truck and tow dolly straight and on level ground. Fully apply the towed vehicle and

truck parking brakes. Install drive shaft on rear-wheel or four-wheel drive towed vehicle.

2. Remove tire straps and safety chains from towed

vehicle, placing the ratchet handle in the down position.

3. Release tow dolly platform locking pin.

4. Release parking brake on towed vehicle.

5. Slowly back towed vehicle off of tow dolly to prevent bottom of vehicle from contacting

ramps. Check transmission fluid level on towed vehicle if drive shaft was removed as fluid may

have leaked out during towing.

6. Return tow dolly platform to the up position and engage locking pin.

7. Take up excess slack of tire straps in ratchet assembly and place safety chains in storage

position.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: