Airaid Intake System 1991-2001 (310-136).pdf

#310-136 INSTALLATION INSTRUCTIONS

91-01 Jeep Cherokee 4.0L

Thank you for purchasing the Airaid Intake System. Please read the instruction manual carefully before

proceeding with the installation. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for

questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully

inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are

missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should

be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The

air filter is reusable and should be cleaned using the Airaid Filter Tune-Up Kit periodically.

Thank you for selecting Airaid.

Packing List:

Packing List (cont’d):

- KIT6WSAPZ

700-450

Airaid Premium Filter 1

#6 Flat Washer

KIT136RFC

Right Panel Black

- KIT15DHC3050

¼-20 Bolt

KIT136MAFC

MAF Panel Black

- KIT09LWZ025

¼” Lock Washer

KIT136A

136 Plastic Adapter Tube 1

- KIT106CAP

Rubber Cap

KITWSTRIP02

Weather Strip 32 ½”

- KITHOSE02

½” x 7” Hose

- KITSNP16M4

#16 Speed Clamp

KIT136HP

Hardware Pack

Tools Required for this Installation:

Flat Head Screwdriver

Phillips Screwdriver

- KIT6C31MXPPZ

6-32 x 5/16” Screw

- KIT6CNKEPZ

6-32 Nut

Installation Instructions. Read Me!

DISCONNECT NEGATIVE (-)

BATTERY CABLE

Remove Factory Air Box Lid

a) Loosen the factory intake tube clamp at the air box lid

using a flat head screwdriver. Refer to Fig #1

1991-1995 Models Only:

b) Remove the vacuum hose located on the driver side rear

of the factory air box and the small vacuum line where it

attaches to the intake manifold. Be Careful with the

plastic line as it is fragile. Refer to Fig #1

Fig#1

c) Remove the large vacuum hose from the passenger side

of the factory air box lid. Refer to Fig #1

d) Unclip the factory air box lid and remove from engine

compartment. See Fig #1

III Assemble the Airaid Intake System

a) Mount the black plastic adapter tube onto the Airaid

Cool Air Dam and fasten using the two ½-20 button

head bolts and two lock washers provided. See Fig #2

b) Assemble the two Airaid Cool Air Dam panels using the

small screws, nuts, and washers provided. See Fig #2

IV Install the Airaid Intake System

a) Position the Airaid Cool Air Dam in place of the factory

original air box lid and snap into place. See Fig #3

b) Clamp the factory tube onto the Airaid plastic tube using

the factory hose clamp. Refer to Fig #3

1991-1995 Models Only:

c) Reattach the small vacuum line on the driver’s side of

the air dam. Replace the short factory hose located on

the driver side of the engine compartment with the

longer ½” hose and secure using the two #16 black

Speed clamps included. Refer to Fig #3 &#4

d) Reattach the single vacuum hose to the Airaid plastic

adapter tube. Refer to Fig #3

1995-2000 Models Only:

e) Plug the remaining nipple on the driver’s side of the

Airaid tube with the black rubber cap provided. Refer

to Fig #4

f) Mount the Airaid Premium Filter to the plastic adapter

inside the air dam. Refer to Fig #3

g) Press the provided weather seal onto the top rim of the

Airaid system. Refer to Fig #3 ( Hint: Start at a corner

of the air dam for ease of installation.)

Fig#2

Fig#3

91-95: attach 6 ¼”

hose provided to

plastic tube. (Shown)

Finishing Up

a) Inspect overall work and check hood clearance.

b) Ensure that no foreign objects are in the intake path!

c) Re-connect negative battery cable.

95-00: Plug nipple on

plastic tube with

rubber cap provided.

(Not Shown)

Fig#4

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: