3391ch7.pdf

(347 KB) Pobierz
Microelectronics, Second Edition
7
Digital Logic Families
7.1 Introduction
.........................................
7 -1
7.2 Transistor-Transistor Logic
...........................
7 -2
7.3 CMOS Logic
.........................................
7 - 6
7.4 Emitter-Coupled Logic
...............................
7 - 10
7.5 Programmable Logic
.................................
7 -13
Robert J. Feugate, Jr.
•
7.1 Introduction
Digital devices are constrained to two stable operat-
ing regions (usually voltage ranges) separated by a
transition region through which the operating point
may pass but not remain (see Fig. 7.1). Prolonged
operation in the transition region does not cause
harm to the devices, it simply means that the result-
ing outputs are unspecified. For the inverter shown
in the figure, the output voltage is guaranteed to
be greater than V OH as long as the input voltage is
below the specified V IH . Note that the circuit is de-
signed so that the input high voltage is lower than
the output high voltage (vice versa for logic low volt-
ages). This difference, called noise margin , permits
interfering signals to corrupt the logic voltage with-
in limits without producing erroneous operation. Logical conditions and binary numbers can be repre-
sented physically by associating one of the stable voltage ranges with one logic state or binary value and
identifying the other stable voltage with the opposite state or value. By extension, then, it is possible to
design electronic circuits that physically perform logical or arithmetic operations. As detailed examination
of logic design is beyond the scope of this chapter, the reader is referred to any of the large number of
digital logic textbooks. 1
Digital logic components were the earliest commercially produced integrated circuits. Resistor-transistor
logic (RTL) and a speedier variant resistor-capacitor-transistor logic (RCTL) were introduced in the early
1960s by Fairchild Semiconductor Diode-transistor logic (DTL) was introduced a few years later by Signetics
Corporation. Although these families are often discussed in electronics texts as ancestors of later logic
families, they have been obsolete for many years and are of historical interest only.
HIGH SUPPLY VOLTAGE
HIGH LOGIC LEVEL
V OH
V IH
V
I
V O
TRANSITION REGION
OL
LOW LOGIC LEVEL
V
IL
LOW SUPPLY VOLTAGE
FIGURE 7.1 Logic voltage levels.
1 Two excellent recent logic design texts are Modern Digital Design , by Richard Sandige, McGraw-Hill, New York,
1990 and Contemporary Logic Design , by Randy Katz, Benjamin Cummings, Redwood City, CA, 1994.
7 - 1
© 2006 by Taylor & Francis Group, LLC
V
752745808.007.png
7 -2
Microelectronics
A primary performance characteristic of different logic families is their speed-power product , that is, the
average propagation delay of a basic gate multiplied by the average power dissipated by the gate. Table 7.1
lists the speed-power product for several popular logic families. Note that propagation delays specified in
manufacturer handbooks may be measured under different loading conditions, which must be taken into
account in computing speed-power product.
7.2 Transistor-Transistor Logic
First introduced in the 1960s, transistor-transistor logic (TTL) was the technology of choice for discrete
logic designs into the 1990s, when complementary metal oxide semi-conductor (CMOS) equivalents
gained ascendancy. Because TTL has an enormous base of previous designs, is available in a rich variety of
small-scale and medium-scale building blocks, is electrically rugged, offers relatively high-operating speed,
and has well-known characteristics, transistor-transistor logic continues to be an important technology
for some time. Texas Instruments Corporation’s 54/7400 TTL series became a de facto standard, with its
device numbers and pinouts used by other TTL (and CMOS) manufacturers.
There are actually several families of TTL devices having circuit and semiconductor process variations
that produce different speed-power characteristics. Individual parts are designated by a scheme combining
numbers and letters to identify the exact device and the TTL family. Parts having 54 as the first digits have
their performance specified over the military temperature range from
−
55 to
+
125 ◦ C, whereas 74-series
70 ◦ C. Letters identifying the family come next, followed by a number
identifying the part’s function. For example, 7486 identifies a package containing four, 2-input exclusive-
OR gates from the standard TTL family, whereas 74ALS86 indicates the same function in the low-power
Schottky family. Additional codes for package type and, possibly, circuit revisions may also be appended.
Generally speaking, devices from different TTL families can be intermixed, although attention must be
paid to fanout (discussed subsequently) and noise performance.
The basic building block of standard TTL is the NAND gate shown in Fig. 7.2 . If either input A or
B is connected to a logic-low voltage, multiple-emitter transistor Q1 is saturated, holding the base of
transistor Q2 low and keeping it cut off. Consequently, Q4 is starved of base current and is also off, while
Q3 receives base drive current through resistor R2 and is turned on, pulling the output voltage up toward
V cc . Typical high output voltage for standard TTL circuits is 3.4 V. On the other hand, if both of the inputs
are high, Q1 moves into the reverse-active region and current flows out of its collector into the base of Q2.
Q2 turns on, raising Q4’s base voltage until it is driven into saturation. At the same time, the Ohm’s law
voltage drop across R2 from Q2’s collector current lowers the base voltage of Q3 below the value needed
to keep D1 and Q3’s base-emitter junction forward biased. Q3 cuts off, with the net result that the output
is drawn low, toward ground. In normal operation, then, transistors Q2, Q3, and Q4 must move between
+
© 2006 by Taylor & Francis Group, LLC
parts are specified from 0 to
752745808.008.png
Digital Logic Families
7 -3
V cc
R4
130
R1
4 K
R2
1.6 K
Q3
INPUT A
Q1
Q2
D1
INPUT B
OUTPUT
Da
Db
Q4
R3
1 K
FIGURE 7.2 Two input standard TTL NAND gate.
saturation and cutoff. Saturated transistors experience an accumulation in minority carriers in their base
regions, and the time required for the transistor to leave saturation depends on how quickly excess carriers
can be removed from the base. Standard TTL processes introduce gold as an impurity to create trapping
sites in the base that speed the annihilation of minority electrons. Later TTL families incorporate circuit
refinements and processing enhancements designed to reduce excess carrier concentrations and speed
removal of accumulated base electrons.
Because the internal switching dynamics differ and because the pull-up and pull-down transistors have
different current drive capabilities, TTL parts show a longer propagation time when driving the output from
low to high than from high to low (see Fig. 7.3). Although the average propagation delay (( t phl +
t plh )
INPUT
REF. VOLTAGE (1.5 V )
t plh
t phl
OUTPUT
FIGURE 7.3 Propagation delay times.
© 2006 by Taylor & Francis Group, LLC
2)
is often used in speed comparisons, conservative designers use the slower propagation delay in computing
circuit performance. NAND gate delays for standard TTL are typically 10 ns, with guaranteed maximum
t phl of 15 ns and t phl of 22 ns.
When a TTL gate is producing a low output, the output voltage is the collector-to-emitter voltage of
pull-down transistor Q4. If the collector current flowing in from the circuits being driven increases, the
output voltage rises. The output current, therefore, must be limited to ensure that output voltage remains
in the specified logic low range (less than V OL ). This places a maximum on the number of inputs that can
be driven low by a given output stage; in other words, any TTL output has a maximum low-level fanout.
/
752745808.009.png 752745808.010.png 752745808.001.png 752745808.002.png
7 -4
Microelectronics
Similarly, there is a maximum fanout for high logic levels. Since circuits must operate properly at either
logic level, the smaller of the two establishes the maximum overall fanout. That is
fanout
=
minimum(
−
I OH ,max /
I IH ,max ,
−
I OL ,max /
I IL ,max )
where
I OH ,max =
specified maximum output current for V OH ,min
I OL ,max
=
specified maximum output current for V OL ,max
I IH ,max
=
specified maximum input current, high level
I IL ,max
=
specified maximum input current, low level
The minus sign in the fanout computations arises because both input and output current reference
directions are defined into the device. Most parts in the standard TTL family have a fanout of 10 when
driving other standard TTL circuits. Buffer circuits with increased output current capability are available
for applications such as clock signals that must drive an unusually large number of inputs. TTL families
other than standard TTL have different input and output current specifications; fanout computations
should be performed whenever parts from different families are mixed.
One of the transistors in the conventional totem pole TTL output stage is always turned on, pulling the
output pin toward either a logic high or low. Consequently, two or more outputs cannot be connected to the
same node; if one output were attempting to drive a low logic voltage and the other a high, a low-resistance
path is created from between V cc and ground. Excessive currents may damage the output transistors and,
even if damage does not occur, the output voltage settles in the forbidden transition region between V OH
and V OL . Some TTL parts are available in versions with open-collector outputs, truncated output stages
having only a pull down transistor (see Fig. 7.4). Two or more open-collector outputs can be connected
to V cc through a pull-up resistor, creating a wired-AND phantom logic gate. If any output transistor is
turned on, the common point is pulled low. It only assumes a high voltage if all output transistors are
turned off. The pull-up resistor must be large enough to ensure that the I OL specification is not exceeded
when a single gate is driving the output low, but small enough to guarantee that input leakage currents will
not pull the output below V OH when all driving gates are off. Since increasing the pull-up resistor value
increases the resistance-capacitance (RC) time constant of the wired-AND gate and slows the effective
propagation delay, the pull-up resistor is usually selected near its minimum value. The applicable design
equations are
( V cc −
V OL ,max )
/
( I OL ,max +
nI IL ,max )
<
R pu <
( V cc −
V OH ,min )
/
( mI OH ,max +
nI IH ,max )
where m is the number of open collector gates connected to R pu and n is the number of driven inputs.
Reference direction for all currents is into the device pin.
V
cc
R
pu
OUTPUT
DRIVE CIRCUITRY
WIRED-AND GATE
DRIVE CIRCUITRY
FIGURE 7.4 Wired-AND gate using open collector outputs and a pullup resistor.
© 2006 by Taylor & Francis Group, LLC
752745808.003.png
Digital Logic Families
7 -5
Some TTL parts have three-state outputs: totem pole outputs that have the added feature that both
output transistors can be turned off under the control of an output enable signal. When the output enable
is in its active state, the part’s output functions conventionally, but when the enable is inactive, both
transistors are off, effectively disconnecting the output pin from the internal circuitry. Several three-state
outputs can be connected to a common bus, and only one output is enabled at a time to selectively place
its logic level on the bus.
Over the long history of TTL, a number of variants have been produced to achieve faster speeds, lower
power consumption, or both. For example, the 54/74L family of parts incorporated redesigned internal
circuitry using higher resistance values to lower the supply current, reducing power consumption to a little
as 1/10 that of standard TTL. Speed was reduced as well, with delay times as much as three times longer.
Conversely, the 54/74H family offered higher speeds than standard TTL, at the expense of increased power
consumption. Both of these TTL families are obsolete, their places taken by various forms of Schottky
TTL.
As noted earlier, TTL output transistors are driven
well into saturation. Rather than using gold dop-
ing to hasten decay of minority carriers, Schottky
transistors limit the forward bias of the collector-
base junction and, hence, excess base minority car-
rier accumulation by paralleling the junction with
a Schottky (gold-semiconductor) diode, as shown
in Fig. 7.5. As the NPN transistor starts to satu-
rate, the Schottky diode becomes forward biased.
This clamps the collector-base junction to about
0.3 V, keeping the transistor out of hard saturation.
Schottky TTL (S) is about three times faster than
standard TTL, while consuming about 1.5 times as
much power.
Lower power Schottky TTL (LS) combined an improved input circuit design with Schottky transistors
to reduce power consumption to a fifth of standard TTL, while maintaining equal or faster speed. The
redesigned input circuitry of LS logic changes the input logic thresholds, resulting in slightly reduced noise
margin.
Still another TTL family is Fairchild Advanced Schottky TTL (FAST). The F parts combine circuit im-
provements with processing techniques that reduce junction capacitances and increase transistor speeds.
The result is a fivefold increase in speed compared to standard TTL, with lowered power consumption.
As their names imply, advanced Schottky (AS) and advanced low-power Schottky (ALS) use improved
fabrication processes to improve transistor switching speeds. Parts from these families are two to three
times faster than their S and LS equivalents, while consuming half the power. Although the standard TTL,
Schottky (S), and low-power Schottky (LS) families remain in volume production, the newer advanced
Schottky families (AS, ALS, F) offer better speed-power products and are favored for new designs.
In making speed comparisons between different logic families, one should keep in mind that man-
ufacturer’s published specifications use different load circuits for different TTL families. For example,
propagation delays of standard TTL are measured using a load circuit of a 15-pF capacitor paralleled
by a 400-
SCHOTTKY
DIODE
FIGURE 7.5 Schottky transistor construction and
symbol.
. Since effective propagation delay increases
approximately linearly with the capacitance of the load circuit, direct comparisons of raw manufacturer
data is meaningless. Manufacturer’s databooks include correction curves showing how propagation delay
changes with changes in load capacitance.
As outputs change from one logic state to another, sharp transients occur on the power supply current.
Decoupling capacitors are connected between the V cc and ground leads of TTL logic packages to provide
filtering, minimizing transient currents along the power supply lines and reducing noise generation.
Guidelines for distribution of decoupling capacitors are found in manufacturer handbooks and texts on
digital system design, for example, Barnes (1987).
© 2006 by Taylor & Francis Group, LLC
resistor, whereas FAST uses 50 pF and 500
752745808.004.png 752745808.005.png 752745808.006.png
Zgłoś jeśli naruszono regulamin