quick setup rb133c.pdf

RouterBOARD 133

Quick Setup Guide and Warranty Information

Board Build Versions

● RB133 – complete build

● RB133c – only one (top) MiniPCI slot, one Ethernet port, 16MB of RAM, no heatsink, no fan header

Assembling the Hardware

First use of the board:

● Insert the MiniPCI cards. RouterBOARD 133 provides three MiniPCI slots:

two on the top of the board, and one additional on the bottom side of

the board. RouterBOARD 133c has only one top MiniPCI slot.

● Connect antenna cables to the MiniPCI cards.

● Install the board in a case and connect other peripherals and cables.

● Plug in power cable to turn on the board.

Powering

The board accepts powering from either the power jack or the LAN1 Ethernet

port:

● direct-input power jack J7 (5.5mm outside and 2mm inside diameter,

female, pin positive plug) accepts 9..28 V DC (overvoltage protection

starts at 30V).

● LAN1 Ethernet port J8 accepts 9..28 V DC input (at the board; higher

voltage needed to compensate for power loss on long cables; at least

18V suggested) from non-standard (passive) Power over Ethernet

injectors (no power over datalines). The board does not work with

IEEE802.3af compliant 48V power injectors.

The maximum output of the power supply available for extension cards is normally 10W (3.0A).

Booting process

First, RouterBOOT loader is started. It displays some useful information on the onboard RS232C asynchronous serial port. The

serial port is set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity. Note that the device does not fully implement

the hardware (RTS/CTS) flow control, so it is suggested to try to disable hardware flow control in the terminal emulation

program in case the serial console does not work as expected, and if it does not help, make a new cable using the pinout

given in the User's manual. The loader may be configured to boot the system from the onboard NAND, and/or from network.

See the respective section of User's manual on how to configure booting sequence and other BIOS parameters.

DHCP or BOOTP (configurable in loader) protocols allow the RouterBOARD 133 series board to get an initial IP address, and

provide the address of a TFTP server to download an ELF boot image from. It is especially useful for software installation. See

the User's manual for more information and protocol details. Note that you must connect the RouterBOARD you want to boot

and the BOOTP/DHCP and TFTP servers to the same broadcast domain (i.e., there must not be any routers between them –

they must be on the same Ethernet switch).

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.

rev. A (5-Dec-2006)

Extension Slots and Ports

● Three Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight

or cross-over cables for connecting to other network devices. The first Ethernet port accepts 9..28 V DC powering from

a passive PoE injector. The other two Ethernet ports do not support PoE powering.

● Three MiniPCI Type IIIA/IIIB ports with 3.3V power signaling.

● DB9 RS232C asynchronous serial port.

Operating System Support

Currently tested operating system is MikroTik RouterOS (starting from version 2.9.38).

law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder.

RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered

trademarks appearing in this manual are the property of their respective holders.

Hardware . MikroTikls SIA warrants all RouterBOARD series equipment for the term of one year from the shipping date to be

free of defects in materials and workmanship under normal use and service. All parts will be repaired or replaced with similar

or functionally equivalent parts by MikroTikls SIA during the warranty term, except in case the returned parts have

mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts

of nature.

Parts (or systems) must be shipped pre-paid to our facility in Riga, Latvia. All items must have a Return Material

Authorization (RMA) which you can get by contacting us via email, telephone or fax. RMA must be printed, signed, and

enclosed with the shipment, also the RMA number must be written on the package itself. Parts sent without following the

proper procedure will be treated as those not to be repaired or replaced due to the above mentioned conditions. Items proved

to be free of defects in our lab will be returned to the customer at the customer's expense. Those that do meet the warranty

repair requirements will be repaired or replaced, and returned to the customer's location at our expense, extending the

warranty term for the time the items are being shipped to and from our facility and replaced or repaired.

Manual . This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,

the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to

ensure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies,

typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect,

incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data

or profits. Please report any inaccuracies found to docs@mikrotik.com .

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.

rev. A (5-Dec-2006)

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: