PT100.pdf

(213 KB) Pobierz
Precision Temperature-Sensing with RTD Circuits
M
AN687
Precision Temperature-Sensing With RTD Circuits
Author: Bonnie C. Baker
Microchip Technology Inc.
Precision Current Source <1 mA
INTRODUCTION
The most widely measured phenomena in the process
control environment is temperature. Common ele-
ments, such as Resistance Temperature Detectors
(RTDs), thermistors, thermocouples or diodes are used
to sense absolute temperatures, as well as changes in
temperature. For an overview and comparison of these
sensors, refer to Microchip’s AN679, “Temperature-
Sensing Technologies ”, DS00679.
Of these technologies, the platinum RTD temperature-
sensing element is the most accurate and stable over
time and temperature. RTD element technologies are
constantly improving, further enhancing the quality of
the temperature measurement (see Figure 1). Typi-
cally, a data acquisition system conditions the analog
signal from the RTD sensor, making the analog
translation of the temperature usable in the digital
domain.
This application note focuses on circuit solutions that
use platinum RTDs in their design. Initially, the RTD
temperature-sensing element will be compared to the
negative temperature coefficient (NTC) thermistor,
which is also a resistive temperature-sensing element.
In this forum, the linearity of the RTD will be presented
along with calibration formulas that can be used to
improve the off-the-shelf linearity of the element. For
additional information concerning the thermistor tem-
perature sensor, refer to Microchip’s AN685, “Ther-
mistors in Single Supply Temperature Sensing
Circuits” , DS00685. Finally, the signal-conditioning
path for the RTD system will be covered with
application circuits from sensor to microcontroller.
V OUT
RTD, most popular element
is made using platinum,
typically 100
Ω
@ 0
°
C
FIGURE 1: Unlike thermistors, RTD
temperature-sensing elements require current
excitation.
RTD OVERVIEW
The acronym “RTD” is derived from the term “Resis-
tance Temperature Detector”. The most stable, linear
and repeatable RTD is made of platinum metal. The
temperature coefficient of the RTD element is positive.
This is in contrast to the NTC thermistor, which has a
negative temperature coefficient, as is shown graphi-
cally in Figure 2. An approximation of the platinum RTD
resistance change over temperature can be calculated
by using the constant 0.00385
Ω
/
Ω
EQUATION
RTD T
=
RTD 0
+
TRTD 0
×
0.00385
ΩΩ
⁄
°
C
where:
RTD(T) is the resistance value of the RTD element at
temperature (Celsius),
RTD 0 is the specified resistance of the RTD element
at 0°C and,
T is the temperature environment that the RTD is
placed (Celsius).
2003 Microchip Technology Inc.
DS00687B-page 1
/°C. This constant is
easily used to calculate the absolute resistance of the
RTD at temperature.
()
×
⁄
648929936.026.png 648929936.027.png 648929936.028.png 648929936.029.png 648929936.001.png
AN687
100
The linearity performance of a typical RTD is shown in
Figure 3.
Thermistor
10
RTD
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
-200 -100 0 100 200 300 400 500 600 700 800
1
0.1
0.01
0.001
0.0001
-100 50
0
50 100 150 200 250 300
Temperature (
°
C)
FIGURE 2: The temperature vs. resis-
tance characteristics of the RTD sensing element
is considerably different than the thermistor sen-
sor element. The RTD sensing element has a
positive temperature coefficient and is
considerably more linear.
The RTD element resistance is extremely low when
compared to the resistance of a NTC thermistor
element, which ranges up to 1 M
Temperature (°C)
at 25°C. Typical
specified 0°C values for RTDs are 50, 100, 200, 500,
1000 or 2000
Ω
FIGURE 3: The linearity error of the
platinum RTD temperature sensor is small when
compared to other sensors, such as the
thermocouple and thermistor.
The RTD element requires a current excitation. If the
magnitude of the current source is too high, the element
will dissipate power and start to self-heat. Consequently,
care should be taken to insure that
platinum
RTD is the most stable over time and linear over
temperature.
If the RTD element is excited with a current reference
at a level that does not create an error due to self-heat-
ing, the accuracy can be ±4.3°C over its entire temper-
ature range of -200°C to 800°C. If a higher accuracy
temperature measurement is required, the linearity for-
mula below (Calendar-Van Dusen Equation) can be
used in a calculation in the controller engine or be used
to generate a look-up table.
Ω
. Of these options, the 100
Ω
≤
1 mA of current is
used to excite the RTD element.
The advantages and disadvantages of the RTD
temperature sensing element is summarized in
Table 1.
TABLE 1:
RTD TEMPERATURE SENSING
ELEMENT ADVANTAGES AND
DISADVANTAGES
Advantages Disadvantages
Very Accurate and Stable Expensive Solution
Fairly Linear to ±4%
RTD T
=
RTD 0
1ATBT 2
++
–
100CT 3
+
CT 4
°
C
Requires Current
Excitation
where:
RTD(T) is the resistance of the RTD element at tem-
perature,
RTD 0 is the specified resistance of the RTD element
at 0°C ,
T is the temperature that is applied to the RTD ele-
ment (Celsius) and,
A, B, and C are constants derived from resistance
measurements at 0°C, 100°C and 260°C.
Good Repeatability
Danger of Self-Heating
Low Resistive Element
RTD CURRENT EXCITATION CIRCUIT
For best linearity, the RTD sensing element requires a
stable current reference for excitation. This can be
implemented in a number of ways, one of which is
shown in Figure 4. In this circuit, a voltage reference,
along with two operational amplifiers, are used to
generate a floating 1 mA current source.
DS00687B-page 2
2003 Microchip Technology Inc.
()
648929936.002.png 648929936.003.png
AN687
R 2
R 1
Solving these equations, the voltage drop across the
reference resistor, R REF , is equal to:
−
1/2
MCP602
EQUATION
1mA
R REF = 2.5 k
Ω
+
V RREF
=
V OUT A1
–
V OUTA 2
A 1
V RREF
=
2
(
–
V R 4
)
–
(
V REF
–
V R 4
–
V R 3
)
REF
−
1/2
R 3
R 4
V REF
=2.5V
V RREF
=
V REF
MCP602
+
where:
V RREF is the voltage across the reference resistor,
R REF and,
V R3 is the voltage drop across R 3
A 2
+
R W
R W
R 1 =R 2 =R 3 =R 4 =25k
Ω
−
R W
The current through R REF is equal to:
FIGURE 4: A current source for the RTD
element can be constructed in a single-supply
environment from two operational amplifiers and
a precision voltage reference.
This is accomplished by applying a 2.5V precision volt-
age reference to R 4 of the circuit. Since R 4 is equal to
R 3 , and the non-inverting input to A 1 is high-imped-
ance, the voltage drop across these two resistors is
equal. The voltage between R 3 and R 4 is applied to the
non-inverting input of A 1 . That voltage is gained by
(1 + R 2 /R 1 ) to the output of the amplifier and the top of
the reference resistor, R REF . If R 1 = R 2 , the voltage at
the output of A 1 is equal to:
EQUATION
I RTD
=
V REF / R REF
This circuit generates a current source that is ratio met-
ric to the voltage reference. The same voltage refer-
ence can be used in other portions of the circuit, such
as the analog-to-digital (A/D) converter reference.
Absolute errors in the circuit will occur as a consequence
of the absolute voltage of the reference, the initial offset
voltages of the operational amplifiers, the output swing
of A 1 , mismatches between the resistors, the absolute
resistance value of R REF and the RTD element. Errors
due to temperature changes in the circuit will occur as a
consequence of the temperature drift of the same ele-
ments listed above. The primary error sources over tem-
perature are the voltage reference, offset drift of the
operational amplifiers and the RTD element.
EQUATION
V OUT A1
=
(
1R 2 /R 1
+
)
×
(
V REF
–
V R 4
)
V OUT A1
=
2
×
(
REF
–
V R 4
)
where:
V OUTA1 is the voltage at the output of A 1 and
V R4 is the voltage drop across R 4 .
RTD SIGNAL-CONDITIONING PATH
Changes in resistance of the RTD element over tem-
perature are usually digitized through an A/D conver-
sion, as shown in Figure 5. The current excitation
circuit, shown in Figure 4, is used to excite the RTD
element. With this style of excitation, the magnitude of
the current source can be tuned to 1 mA or less by
adjusting R REF . The voltage drop across the RTD ele-
ment is sensed by A 3 , then gained and filtered by A 4 .
With this circuit, a 3-wire RTD element is selected.
This configuration minimizes errors due to wire
resistance and wire resistance drift over temperature.
The voltage at the output of A 2 is equal to:
EQUATION
V OUTA 1
=
V REF
–
V R 4
–
V R 3
This same voltage appears at the inverting input of A 2
and across to the non-inverting input of A 2 .
2003 Microchip Technology Inc.
DS00687B-page 3
×
648929936.004.png 648929936.005.png 648929936.006.png
AN687
R
A 1
R
Current
Generator
Circuit
1/4
MCP602
−
+
1mA
R REF = 2.5 k
Ω
V REF = 2.5V
1/4
MCP602
A 2
R
R
+
V IN
R 2 = 100 k
Ω
C 3
R 1 =100 k
Ω
A 3
R W 1
1/4
MCP604
R 3
R 4
A 4
+
V REF
1/4
MCP604
−
C 4
+
+IN
R W 2
V SS
MCP3201
R 5
R W 2
R 6
FIGURE 5:
This circuit uses a RTD temperature-sensitive element to measure temperatures from
C. The current generator circuit from Figure 4 excites the sensor. An operational amplifier
(A 3 ) is used to zero wire resistance error. A fourth amplifier (A 4 ) is used to gain the signal and filter possible
alias interference. A 12-bit converter (MCP3201) converts the voltage across the RTD to digital code for the
8-pin controller (PIC12C508).
°
DS00687B-page 4
2003 Microchip Technology Inc.
−
−
–IN
-200°C to 600
648929936.007.png 648929936.008.png 648929936.009.png 648929936.010.png 648929936.011.png 648929936.012.png 648929936.013.png 648929936.014.png 648929936.015.png 648929936.016.png 648929936.017.png 648929936.018.png 648929936.019.png 648929936.020.png 648929936.021.png 648929936.022.png 648929936.023.png 648929936.024.png
AN687
at 0°C. If
the RTD is used to sense temperature over its entire
range of -200°C to 600°C, the range of resistance pro-
duced by the RTD would be nominally 23
Ω
REFERENCES
.
Since the resistance range is relatively low, wire resis-
tance and wire resistance change over temperature can
skew the measurement of the RTD element. Conse-
quently, a 3-wire RTD device is used to reduce these
errors.
The errors contributed by the wire resistances, R W1
and R W3 , are subtracted from the circuit with A 3 , the
operational amplifier circuit. In this configuration, R 1
and R 2 are equal and are relatively high. The value of
R 3 is selected to ensure that the leakage currents
through the resistor do not introduce errors to the cur-
rent in the RTD element. The transfer function of this
portion of the circuit is:
Ω
to 331
Ω
AN679, “Temperature Sensing Technologies”,
DS00679, Baker, Bonnie, Microchip Technology Inc.
“Practical Temperature Measurements”, OMEGA
CATALOG, pg Z-11
AN684, “Single-Supply Temperature Sensing with
Thermocouples”, DS00684, Baker, Bonnie, Microchip
Technology Inc.
AN682, “Using Operational Amplifiers for Analog Gain
in Embedded System Design”, DS00682, Baker, Bon-
nie, Microchip Technology Inc.
AN685, “Thermistors in Single-Supply Temperature-
Sensing Circuits”, DS00685, Baker, Bonnie, Microchip
Technology Inc.
“Evaluating Thin Film RTD Stability”, SENSORS, Hyde,
Darrell, OCT. 1997, pg 79
“Refresher on Resistance Temperature Devices”,
Madden, J.R., SENSORS, Sept., 1997, pg 66
“Producing Higher Accuracy From SPRTs (Standard
Platinum Resistance Thermometer)”, MEASUREMENT
& CONTROL, Li, Xumo, June, 1996, pg118
EQUATION
V OUTA 3
=
(
V IN
–
V w1
)
(
1R 2 / R 1
)
–
V IN
(
R 2 /R 1
)
where:
V IN = V W1 +V RTD +V W3 ,
V Wx is the voltage drop across the wires to and from
the RTD and
V OUTA 3 is the voltage at the output of A 3 .
If it is assumed that
R 1 = R 2 and R W1 = R W3
the transfer function above reduces to:
V OUTA3 = V RTD
The voltage signal at the output of A 3 is filtered with a
2 nd order, low pass filter created with A 4 , R 3 , C 3 , R 4 and
C 4 . This same signal is also gained by the resistors R 5
and R 6 .
CONCLUSION
Although the RTD requires more circuitry in the signal-
conditioning path than the thermistor or the silicon tem-
perature sensor, it ultimately provides a high-precision,
relatively linear result over a wider temperature range.
If further linearization is performed in the controller, the
RTD circuit can achieve ±0.01°C accuracy.
2003 Microchip Technology Inc.
DS00687B-page 5
In this circuit, the RTD element equals 100
+
648929936.025.png
Zgłoś jeśli naruszono regulamin