CD-S2000.pdf

SUPER AUDIO CD PLAYER

CD-S2000

SERVICE MANUAL

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.

It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already

known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal

injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,

we advise all YAMAHA product owners that any service required should be performed by an authorized

YAMAHA Retailer or the appointed service representative.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and

service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable

and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please

contact the distributor's Service Division.

WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

CONTENTS

TO SERVICE PERSONNEL ...................................... 2–3

PREVENTION OF ELECTROSTATIC DISCHARGE .... 4

FRONT PANEL .............................................................. 5

REAR PANELS .......................................................... 5–7

REMOTE CONTROL PANEL ........................................ 8

SPECIFICATIONS / ࢀߟ࢓༷ ...................................... 8–9

INTERNAL VIEW ........................................................... 9

DISASSEMBLY PROCEDURES ෼ղखॱ . .......... 10–16

TEST MODE / ςετϞʔυ .......................................... 17

UPDATING FIRMWARE / ϑΝʔϜ΢ΣΞͷॻ ͖ ࠐΈ

............................................................................ 18–24

DISPLAY DATA ........................................................... 25

IC DATA ................................................................. 26–28

PIN CONNECTION DIAGRAMS ............................ 29–30

BLOCK DIAGRAM ....................................................... 31

PRINTED CIRCUIT BOARDS . ............................... 32–40

SCHEMATIC DIAGRAMS . ..................................... 41–45

REPLACEMENT PARTS LIST .............................. 47–58

REMOTE CONTROL . ................................................... 59

101078

This manual is copyrighted by YAMAHA and may not be copied or

redistributed either in print or electronically without permission.

P.O.Box 1, Hamamatsu, Japan

'07.12

CD-S2000

TO SERVICE PERSONNEL

AC LEAKAGE

TESTER OR

EQUIVALENT

1. Critical Components Information

Components having special characteristics are marked s

and must be replaced with parts having specifications equal

to those originally installed.

2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify

that all exposed conductive surfaces are properly insulated

from supply circuits.

WALL

OUTLET

EQUIPMENT

UNDER TEST

INSULATING

TABLE

Meter impedance should be equivalent to 1500 ohms shunted

by 0.15 µ F.

Leakage current must not exceed 0.5mA.

Be sure to test for leakage with the AC plug in both polarities.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive

harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY

REASON WHAT SO EVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before

handling food.

About lead free solder / ແԖϋϯμʹ͍ͭͯ

All of the P.C.B.s installed in this unit and solder joints are

soldered using the lead free solder.

ຊػʹ౥ࡌ͞Ε͍ͯΔ͢΂ͯͷج൘͓Αͼϋϯμ෇͚ʹΑΔ઀߹

෦͸ແԖϋϯμͰϋϯμ෇͚͞Ε͍ͯ·͢ɻ

Among some types of lead free solder currently available,

it is recommended to use one of the following types for the

repair work.

ແԖϋϯμʹ͸͍͔ͭ͘ͷछྨ͕͋Γ·͕͢ɺमཧ࣌ʹ͸Լهͷ

Α͏ͳແԖϋϯμͷ࢖༻Λਪ঑͠·͢ɻ

ɾ 4O"H$Vʢऎۜಔʣ

ɾ 4O$Vʢऎಔʣ

ɾ 4O;O#JʢऎѥԖϏεϚεʣ

• Sn + Ag + Cu (tin + silver + copper)

• Sn + Cu (tin + copper)

• Sn + Zn + Bi (tin + zinc + bismuth)

Caution:

As the melting point temperature of the lead free solder is

about 30

C to 40

C (50

F to 70

஫ҙɿ

ແԖϋϯμͷ༥఺Թ౓͸௨ৗͷԖೖΓϋϯμʹൺ΂ʙˆ

ఔ౓ߴ͘ͳ͍ͬͯ·͢ͷͰɺͦΕͧΕͷϋϯμʹ߹ͬͨϋϯμ

ͯ͝Λ͝࢖༻͍ͩ͘͞ɻ

WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation,

which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be

used during servicing of the unit.

1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from

the laser pick-up unit at all times. Do not stare at the laser beam at any time.

2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.

3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in

hazardous radiation exposure.

Laser Emitting conditions:

1) When the top cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit

a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the

lens of the laser pick-up unit. Do not attempt any servicing during this period!

If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser

emissions.

2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory

prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this

manual. Adjustment of this control can increase the laser emission level from the device.

F) higher than that of the lead

solder, be sure to use a soldering iron suitable to each solder.

CD-S2000

Laser Diode Properties

• Material:

SA-CD

Semiconductor laser (AlGaInP)

• Laser Output:

SA-CD

5 mW (max.)

Semiconductor laser (AlGaAs)

7 mW (max.)

• Wavelength:

SA-CD

650 nm

780 nm

B, G models

Warning for power supply

The primary side of the power supply carries live mains voltage when the player is connected to the mains even when

the player is switched off !

This primary area is not shielded so it is possible to touch copper tracks and/or components when servicing the player.

Service personnel have to take precautions to prevent touching this area or components in this area.

Note:

The screws on the DVD mechanism may never be touched, removed or re-adjusted.

Handle the DVD mechanism with care when the unit has to be exchanged!

The DVD mechanism is very sensitive for dropping or giving shocks.

CD-S2000

PREVENTION OF ELECTROSTATIC DISCHARGE

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transis-

tors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of compo-

nent damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on

your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist

strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)”

can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa-

rable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the protective mate-

rial to the chassis or circuit assembly into which the device will be installed.

CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brush-

ing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient

to damage an ES device).

Grounding for electrostatic breakdown prevention

1. Human body grounding.

Use the antistatic wrist strap to discharge the static electricity from your body.

2. Work table grounding.

Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.

Caution:

The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the

optical pickup.

Anti-static wrist strap

1M-ohms

Conductive material

(sheet) or steel sheet

CD-S2000

FRONT PANEL

CD-S2000 (U, C, R, T, K, A, B, G, L, J models)

REAR PANELS

CD-S2000 (U, C models)

CD-S2000 (R model)

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: