wishing well REEL.pdf

Wishing Well Hose Reel Assembly Instructions

Material List

3 ⁄ 4 " X 1 1 ⁄ 2 " - 55'

1 1 ⁄ 2 " O.D. Gal. Steel Pipe - 14"

3 ⁄ 4 " X 2 1 ⁄ 2 " - 26'

1 1 ⁄ 2 " I.D. ABS Pipe - 1"

3 ⁄ 4 " X 3 1 ⁄ 2 " - 4'

7 ⁄ 8 " dia. Dowell - 4"

3 ⁄ 4 " X 5 1 ⁄ 2 " - 13'

3 ⁄ 8 " Rebar - 6'

1 1 ⁄ 2 " X 3 1 ⁄ 2 " - 8'

3 ⁄ 8 " Sisal Rope - 24"

3 ⁄ 4 " angle brackets - 2 ea.

Landscape tie - 6'

Step 1

1 ⁄ 2 " Pipe Brackets - 2 ea.

#8 Flat Head Wood Screws

1 1 ⁄ 4 " - 120 ea. 1 3 ⁄ 4 " - 16 ea. 2 1 ⁄ 2 " - 3 ea.

1 ⁄ 4 " X 3 ⁄ 4 " Carriage Bolt, Nut & Washer - 1 ea.

3 ⁄ 4 " X #8 Sheet Metal Screws - 4 ea.

1 1 ⁄ 2 " Gal. Finishing Nails - 12 ea.

2 1 ⁄ 2 " Gal. Finishing Nails - 12 ea.

Shingle Nails - 1 pkg.

Cedar Shingles to cover 8 sq. feet

1/2" male hose thread adapter - 1 ea.

1/2" copper pipe - 17"

1/2" copper 90° elbows - 2 ea.

brass quick coupler for hose

3 ⁄ 4 " X 1 1 ⁄ 2 " X 10 3 ⁄ 4 " - 12 ea.

30 ° cuts both ends

Bottom Base Frame

3 ⁄ 4 " X 2 1 ⁄ 2 " X 13 7 ⁄ 8 " - 6 ea.

30 ° cuts both ends

Top Base Frame

Cut the peices for the top and bottom frames and

assemble lapping the joints as shown. Fasten each peice

with three 1 1 ⁄ 4 " screws and waterproof glue, see note

below.

3 ⁄ 4 " X 1 1 ⁄ 2 " X 13 1 ⁄ 2 " - 6 ea

30 ° cuts both ends

Top Base Frame

Bottom

Frame

Note:

Use a spacer the thickness of

the panel boards to determine

distance " A", there may be a

space where the narrow frame

boards meet at "B". Dry

assemble entire frame, then

remove pieces one at a time and

add glue.

Top

Frame

"A"

Step 2

"B"

Cut the six wide and twelve narrow panel boards,

assemble the base by fastening panel boards to inside of

top frame and outside of bottom frame with 1 1 ⁄ 4 " screws.

3 ⁄ 4 " X 2 1 ⁄ 2 " X 17 1 ⁄ 4 " - 12 ea.

Base Panel

3 ⁄ 4 " X 5 1 ⁄ 2 " X 17 1 ⁄ 4 " - 6 ea.

MendocMedia ©

Wishing Well Hose Reel

Plan # 104

Base Panel

Page 1

Step 3

1 1 ⁄ 2 " X 3 1 ⁄ 2 " X 48" - 2 ea.

Support Upright

45°

3 ⁄ 4 " x 1 1 ⁄ 2 " X 16" - 2 ea. Short Rafter

3 ⁄ 4 " X 1 1 ⁄ 2 " X 11" - 4 ea. 45°

3 ⁄ 4 " x 1 1 ⁄ 2 " X 16 3 ⁄ 4 " - 2 ea.

Support Brace

Cut the two uprights then drill holes 28" from the square end, one 1 1 ⁄ 2 " and one 1 5 ⁄ 8 " in diameter, then cut the

four rafters and the four support braces. Using one long and one short rafter fasten them to the top of the

uprights with 1 3 ⁄ 4 " screws, repeat for the second one, then fasten the supports with 1 1 ⁄ 4 " screws. Attach

completed roof supports to base with 1 3 ⁄ 4 " screws through wide panel boards.

Step 4 (Optional)

If you are making the roof planter attach two strips 19" long

6" from the top of uprights to hold the plant pot.

Step 5

3 ⁄ 4 " X 1 1 ⁄ 2 " X 24" - 8 ea.

Roof Slat

3 ⁄ 4 " X 1 1 ⁄ 2 " X19" - 4 ea.

Gable Trim

45°

Cut the eight roof slats and four gable trim boards, with 1 1 ⁄ 4 " screws attach

the roof slats spaced as shown, then attach trim boards with 1 3 ⁄ 4 " screws.

1 1 ⁄ 2 "

Step 6 ( Omit and go to step 7 for roof planter )

Trim 6 1 ⁄ 2 " off the butt of each shingle for the first row overhanging the bottom slat by 2" and the trim boards by 1 ⁄ 2 "

nailing into first slat. Lay a second layer covering the joints of the first layer nailing into second slat. Lay a second row

cut to 13" long at the thin end spaced 6 1 ⁄ 2 " from bottom nailing into third slat. Lay a third row 13" from bottom using

the butts cut from first layer nailing into fourth slat. Trim the ridge with 3 ⁄ 8 " thick lath.

MendocMedia ©

Wishing Well Hose Reel

Plan # 104

Page 2

Step 7 (Optional)

11"

If you are making the roof planter cut 11" out of the center of the top two roof slats

on each side, fasten the strips that have been removed to the fixed roof slats as

shown with 1 1 ⁄ 4 " screws. Trim 6 1 ⁄ 2 " off the butt of each of the shingles in the first

row, overhang the bottom slat by 2" and the trim board by 1 ⁄ 2 " nailing into the

bottom slat. Lay a second layer of shingles trimmed at the thin end to 13" long

over the first covering the joints nailing into the second slat. Lay a second row of

13" long shingles on each side of opening nailing into third slat and 6 1 ⁄ 2 " butts cut

from first layer below opening spaced 6 1 ⁄ 2 " from bottom. Lay a third row using

remaining 6 1 ⁄ 2 " butts on each side of opening 13" from bottom. Trim the ridge

with lath or rip shingles as this is only a short span.

Step 8

3 1 ⁄ 2 "

2 1 ⁄ 2 "

1 1 ⁄ 2 "

Cut 4 1 ⁄ 2 " length of 1 1 ⁄ 2 " pipe for short reel support. Drill two

3 ⁄ 16 " dia holes 1 ⁄ 2 " from end of pipe opposite each other. Cut

two slots 1 ⁄ 2 " apart 1 1 ⁄ 4 " long, bend down to form tabs. Insert

short end into 1 1 ⁄ 2 " dia. hole in 2X4 upright and secure

with two 1 1 ⁄ 4 " screws.

Cut crank arm from 3 ⁄ 4 " material as shown above,

round all four corners, drill 1 1 ⁄ 2 " dia. hole 1 3 ⁄ 8 "

from large end and 7 ⁄ 8 " dia. hole 3 ⁄ 4 " from small

end. Insert 4" long dowel in hole and fasten with

glue and 1 1 ⁄ 4 " long screw, drilling pilot hole for

screw.

Cut 9 1 ⁄ 4 " length of 1 1 ⁄ 2 "

dia.pipe, insert into hole in

crank arm and drill 1 ⁄ 4 " hole

through arm and pipe,

fasten with 1 ⁄ 4 " X 1" carrage

bolt and nut.

Step 9

Using a compass set at 2 1 ⁄ 2 " draw a 5" dia circle , mark off 2 1 ⁄ 2 "

arcs around circle to create hexagon on a sheet of paper. Using

this as a pattern cut three hexagons from 1X6 x 3 ⁄ 4 " material. Set

compass at 5" and draw a circle 10" in dia. on sheet of paper.

Fold in half to use as a pattern to cut four semi-circles from 1X6

X 3 ⁄ 4 " stock.

• •

•

Make two spool ends by fastening

a hexagon to two of the semi-

circles alternating the direction of

the grain using glue and wood

screws. Drill a 1 1/2" hole in center

of one and a 1 5/8" hole in center

of other. Drill a 1 1/2" hole in

center of remaining hexagon.

•

Cut two spacers 1 ⁄ 2 " wide from 1 1 ⁄ 2 " I.D ABS pipe.

Step 10

Slide spacer on to stub, then spool end with 1 5 ⁄ 8 "

hole. Fasten angle brackets to hexagon on spool

end and single hexagon even with the center holes

with 3 ⁄ 4 " X #8 sheet metal screw. Insert crank through

other upright, slide on spacer, then spool side, then

hexagon. Drill 1 ⁄ 8 " pilot holes for #8 X 3 ⁄ 4 " sheet metal

screws to anchor angle brackets to pipe axel. Cut

five 3 ⁄ 4 " X 2 1 ⁄ 2 "baords 12 3 ⁄ 4 " long, attach these to

the three hexagons with 1 1 ⁄ 4 " screws leaving one

side empty for hose to enter to connect to swivel.

2 1 ⁄ 2 "

3 ⁄ 4 " X 2 1 ⁄ 2 " X 12 3 ⁄ 4 " - 5 ea.

MendocMedia ©

Wishing Well Hose Reel

Plan # 104

Page 3

Step 11

Step 12

14 "

8" Lenght

Cut three lengths of 1/2" copper pipe,

51/2", 8" and 3 1/2", solder into U

shape, insert long end through hole in

upright and mark position to drill second

hole 3/4" in dia. Anchor pipe to upright

with 3/4" X 2 1/2" X 6' spacer and the

two pipe brackets with 1 1/4" screws.

Solder hose thread adapter to top pipe

and install quick coupler.

30°

cuts

Make hexagon base using landscape

ties, toenail sections together, drill

3 ⁄ 8 " hole in center of every second

side. Level base for well and drive

24" long lengths of rebar through

holes to anchor base to ground.

Fasten well to base with

2 1 ⁄ 2 " long screws through bottom

frame.

Water supply can be connected to bottom pipe directly with a reducer

and a hose clamp , or an elbow can be soldered on, then a shut off tap

can be plumbed in. The supply line can be buried by cutting into the

sod between well and outside tap.

Cedar Bucket

Start with a 3 ⁄ 4 " X 3 1 ⁄ 2 " X 48" strip and bevel the sides at a 30 ° angle, cut four pieces 7" long and two 8 1 ⁄ 2 "

long. Shape the top of the 8 1 ⁄ 2 " pieces as shown in fig. 1. With a compass measure the distance across

the short edge of the boards, see fig. 2. Using this measurement draw a circle on a 3 ⁄ 4 " X 5 1 ⁄ 2 " X 5 1 ⁄ 2 " piece,

then with the same compass setting mark six arcs around the circumference of the circle, connect each

arc with a line to form a hexagon as in fig. 3. Cut out the hexagon and with 1 1 ⁄ 2 " galvanized finishing nails

fasten the strips to the base and to each other as shown in fig. 4, making sure 8 1 ⁄ 2 " strips are opposite

each other.

1" dia. arcs

1 1 ⁄ 2 "

fig. 2

fig. 1

fig. 3

fig. 4

This is an alternative choice built around the black plastic containers that

plants come in from nurseries and can be done without removing the plant.

Rip shingles to about 1 3 ⁄ 4 " wide, cut them to the length of the pot. Plane the strips so they are

tapered about a 1 ⁄ 4 " at the thin end, this will depend on pot, and at an angle so they butt together,

drill a hole in the strip and fasten it to outside of pot with a short screw, this is somewhat of a

trial and error method as the last piece is just cut to fit into the last space. As an added touch

black plastic strapping can be wrapped around the bucket to simulate metal hoops and fastened

with the same short screws. Drill holes on opposite sides for rope handle if required.

MendocMedia ©

Wishing Well Hose Reel

Plan # 104

Page 4

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: