cupola-birdhouse.pdf

(233 KB) Pobierz
Cupola Birdhouse
C
upola Birdhouse
This whimsical birdhouse is mounted on our deck. It's such a treat watching the birds
carry twigs into their house to build the nest! Even if you’re not a bird watcher, you’ll enjoy
seeing this birdhouse in your garden or on your patio.
Materials and Supplies
  1 piece of ½”-thick exterior
plywood, measuring 12” x 24’
  1 piece of 3/8”-thick exterior
plywood, measuring 12” x 36”
  3 linear feet of 1 x 8 pine
  15 linear feet of 1 x 4 pine
  1 linear foot of 1 x 2 pine
  1 decorative curtain rod finial
  3 linear feet of 2”-wide canvas
fabric strips
  Staple gun and staples
  Paneling adhesive
Hardware
  20, 4d 1-1/2” finishing nails
  20, 1-1/4” screws
Cutting List
Code Description Qty.
Materials
Dimensions
A Top/Bottom
2 ½” plywood
11-1/4”diameter circle
B Wide Side
10 1 x 4 pine
11” long
C Narrow Side
1 1 x 2 pine
11” long
D Base Side
4 1 x 4 pine
14-1/2” long
E Base
2 1 x 8 pine
16” long
F Roof Panel
4 1 x 4 pine
12” x 12” x 7” triangle
108257390.046.png 108257390.047.png 108257390.048.png 108257390.049.png 108257390.001.png 108257390.002.png 108257390.003.png 108257390.004.png 108257390.005.png 108257390.006.png 108257390.007.png 108257390.008.png 108257390.009.png 108257390.010.png 108257390.011.png 108257390.012.png 108257390.013.png 108257390.014.png 108257390.015.png 108257390.016.png 108257390.017.png 108257390.018.png 108257390.019.png 108257390.020.png 108257390.021.png 108257390.022.png 108257390.023.png 108257390.024.png 108257390.025.png 108257390.026.png 108257390.027.png 108257390.028.png 108257390.029.png 108257390.030.png 108257390.031.png 108257390.032.png 108257390.033.png 108257390.034.png 108257390.035.png 108257390.036.png 108257390.037.png 108257390.038.png 108257390.039.png 108257390.040.png
Making the House
1. Cut two top/bottoms (A) from ½”-thick plywood, each a circle 11-1/4 inches in diameter.
2. Cut 10 wide sides (B) from 1 x 4 pine, each measuring 11 inches.
3. Cut a 1-1/2”-inch-diameter hole in one wide side (B), 4 inches from one end, and centered on
the width, as shown in Figure 1 . ( Note: Different birds require different size openings. Refer
to a book on building birdhouses to help you determine what size hold to drill. The hole size
used here is a good match for flycatchers, wrens, nut hatches, and tree swallows.)
4. Measure carefully and mark the center of the
1 x 4 width of each of the wide sides (B), 3/8-
inch from each end, as shown in Figure 1.
5. Place one top/bottom (A) on a level surface.
Attach one wide side (B) to the top/bottom
(A). Apply glue to the meeting surfaces, and
nail through the mark on the wide side (B)
into the edge of the top/bottom (A) using a 1-
1/2”-long nail, as shown in Figure 2 .
6. Place a second wide side (B) next to the first
one, so that the inner edges meet. Apply glue
to the meeting surfaces, and nail through the
wide side (B) into the edge of the top/bottom
(A). Continue this procedure to attach the
remaining eight wide sides (B) to the
top/bottom (A).
Figure 1
7. Cut one narrow side (C) from 1 x 2 pine,
measuring 11 inches. Mark the exact center
of the width, 3/8-inch from each end.
8. Attach the narrow side (C) to the top/bottom (A) in the space remaining between the first and
last wide sides (B). Apply glue to the meeting surfaces, and nail through the mark in the
narrow side (C) into the top/bottom (A).
9. Place the remaining top/bottom (A) on a level surface. Turn the house assembly upside-
down, and fit the narrow and wide sides (B and C) over the remaining top/bottom (A).
Apply glue to the meeting surfaces, and nail through the marks to attach each of the sides (B
and C) to the top/bottom (A).
2
108257390.041.png
Making the Base
1. Cut four base sides (D) from 1 x 4 pine, each
measuring 14-1/2 inches.
Figure 2
2. Place two bases (D) on a level surface,
parallel to each other and 14-1/2 inches apart.
Fit the remaining two base sides (D) between
the first two base sides (D), as shown in
Figure 3. Apply glue to the meeting surfaces,
and nail through the overlapping base sides
(D) into the ends of the inner base sides (D),
using two 1-1/2”-long nails on each of the
joints.
4. Fit the two bases (E) over the base sides (D), as shown in Figure 3. Apply glue to the
meeting surfaces, and nail through the edges of the two bases (E) into the base sides (D).
Use four or five 1-1/2-inch-long nails on each side.
3. Cut two bases (E) from 1 x 8 pine, each
measuring 16 inches.
Figure 3
5. Place the house assembly on a level surface, with the drilled hole closer to the top.
6. Turn the base assembly upside down and center it over the house assembly, as shown in
Figure 4. Apply glue to the meeting surfaces, and screw through the both bases (E) into the
top/bottom (A), using five or six 1-1/4-inch screws.
3
108257390.042.png
Figure 4
Making the Roof
1. Cut eight triangular roof panels (F) from 3/8”-thick plywood, each measuring 12 x 12 x 7
inches. These will be joined together to form an eight-sided cone for the roof.
2. To hold the pieces together temporarily, we used small strips of canvas fabric and a staple
gun.
3. Begin by placing two roof panels (F) on a flat surface, with their 12-inch-sides exactly
matching, as shown in Figure 5 . Cut two 2-inch-long strips of canvas fabric. Place one strip
about 2 inches from the top, and one strip about 1 inch from the bottom of the panels. Use a
staple gun to staple the fabric to each of the two roof panels (F).
4. Repeat step 3 to attach the remaining six roof panels (F) to the first two.
5. Now comes the awkward part. You may wish to enlist the assistance of a handy helper for
this step. Have someone hold the assembly so that you can connect the first roof panel to the
eighth roof panel. Again use two fabric strips to connect the panels.
6. Place the connected roof right side up on a level surface. Adjust the panels so that the
assembly is even on all sides. Then apply paneling adhesive into each of the joints to form a
smooth surface. Let the assembly dry overnight.
4
108257390.043.png
Figure 5
Finishing
1. As a finishing touch, we added a curtain rod finial to the top of the roof.
2. If you plan to have visitors to your new birdhouse, it would be a good idea to attach the roof
to the house assembly with a hinge so that you can clean it out. If you don't plan to have
visitors and will simply use it as an ornamental project, you can simply nail through the roof
into the house assembly to hold it in place.
3. Fill any cracks, crevices, or screw holes with wood filler, and thoroughly sand all surfaces of
the completed birdhouse.
4. Seal and paint or stain your birdhouse the colors of your choice.
Try other indoor and outdoor projects from
www.wowimadeit.com !
5
108257390.044.png 108257390.045.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin