HMI_WinCC_flexible_Communication_Part_1.pdf
(
3020 KB
)
Pobierz
SIMATIC HMI WinCC flexible 2007 Communication Part 1
Preface
SIMATIC HMI WinCC flexible 2007 WinCC flexible 2007 Communication Part 1
______________
1
SIMATIC HMI
______________
2
WinCC flexible 2007
Communication Part 1
______________
3
______________
4
User's Manual
______________
5
______________
6
______________
7
______________
8
______________
9
This user's manual is part of the documentation
package with the order number
6AV6691-1CA01-2AB0
07/2007
A5E01056780-01
Working with connections
Communication with
SIMATIC S7 controllers
Communication via
SIMATIC HMI HTTP protocol
Communication via OPC
Communication with
SIMOTION controllers
Communication with
WinAC controllers
Communication with
SIMATIC S5 controllers
Communication with
SIMATIC 500/505 controllers
Appendix
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY
Ordernumber: 6AV6691-1CA01-2AB0
Ⓟ 07/2007
Copyright © Siemens AG 2007.
Technical data subject to change
Safety Guidelines
Preface
Preface
This user manual is part of the WinCC flexible documentation..
The purpose of the "WinCC flexible Communication" user manual is to explain:
● which communications protocols can be used for communication between a SIEMENS
HMI device and a controller,
● which SIEMENS HMI devices can be used for communication,
● which controllers can be connected to a selected SIEMENS HMI device,
● which settings are required in the controller program for the connection, and
● which user data areas must be set up for communication.
Separate sections therefore explain the size, structure, and function of the user data areas
and the assigned area pointers.
The manual is intended for newcomers, operators and configuration engineers involved in
configuration, commissioning, installation and service with WinCC flexible.
The help integrated in WinCC flexible, the WinCC flexible Information System, contains
detailed information. The information system contains instructions, examples and reference
information in electronic form.
Basic Knowledge Requirements
General knowledge in the field of automation engineering is required to understand this
manual.
You should also have experience of using PCs running under the Windows 2000 or
Windows XP operating systems. A knowledge of VBA or VBS is required for advanced
configuration by using scripts.
Scope of the manual
This manual is valid for the WinCC flexible 2007 software package.
WinCC flexible 2007 Communication Part 1
User's Manual, 07/2007, 6AV6691-1CA01-2AB0
3
Preface
Position in the information scheme
This manual is part of the SIMATIC HMI documentation. The information below presents an
overview of the information landscape of SIMATIC HMI.
User manual
● WinCC flexible Micro
– describes the engineering basics based on the WinCC flexible Micro engineering
system (ES)
● WinCC flexible Compact/ Standard/ Advanced
– describes the engineering basics based on the WinCC flexible Compact,
WinCC flexible Standard and WinCC flexible Advanced engineering systems (ES)
● WinCC flexible Runtime:
– Describes how to commission and operate your Runtime project on a PC.
● WinCC flexible Migration:
– Describes how to convert an existing ProTool project to WinCC flexible.
– Describes how to convert an existing WinCC project to WinCC flexible.
– Describes how to migrate ProTool projects with an HMI migration from OP3 to OP 73
or OP 73 micro.
– Describes how to migrate ProTool projects with an HMI migration from OP7 to OP 77B
or OP 77A.
– Describes how to migrate ProTool projects with an HMI migration from OP 17 to
OP 177B.
– describes how to migrate ProTool projects with HMI migration from RMOS graphic
devices to Windows CE devices.
● Communication:
– Communication Part 1 describes the connection of the HMI device to SIMATIC PLCs.
– Communication Part 2 describes the connection of the HMI device to third-party PLCs.
Operating Instructions
● Operating instructions for SIMATIC HMI devices:
– OP 73, OP 77A, OP 77B
– TP 170micro, TP 170A, TP 170B, OP 170B
– OP 73micro, TP 177micro
– TP 177A, TP 177B, OP 177B
– TP 270, OP 270
– TP 277, OP 277
– MP 270B
– MP 370
– MP 377
WinCC flexible 2007 Communication Part 1
4
User's Manual, 07/2007, 6AV6691-1CA01-2AB0
Preface
● Operating instructions for mobile SIMATIC HMI devices:
– Mobile Panel 170
– Mobile Panel 277
– Mobile Panel 277F IWLAN
– Mobile Panel 277 IWLAN
● Operating instructions (compact) for SIMATIC HMI devices:
– OP 77B
– Mobile Panel 170
Getting Started
● WinCC flexible for first time users:
– Based on a sample project, this is a step-by-step introduction to the basics of
configuring screens, alarms, and recipes, and screen navigation.
● WinCC flexible for advanced users:
– Based on a sample project, this is a step-by-step introduction to the basics of
configuring logs, project reports, scripts, user management, and multilingual projects,
and integration into STEP 7.
● WinCC flexible options:
– Based on a sample project, this is a step-by-step introduction to the basics of
configuring the WinCC flexible Audit, Sm@rtServices, Sm@rtAccess and OPC Server
options.
Online availability
The following links provide direct access to technical documentation on SIMATIC products
and systems in English, German, French, Italian, and Spanish.
● SIMATIC Guide Technische Dokumentation in Deutsch:
"
http://www.ad.siemens.de/simatic/portal/html_00/techdoku.htm
"
● SIMATIC Guide for Technical Documentation in English:
"
http://www.ad.siemens.de/simatic/portal/html_76/techdoku.htm
"
Guide
The user manual consists of Parts 1 and 2. Part 1 is organized as follows:
● Basics on communication - Chapter 1
● Connecting to the SIMATIC S7 - Chapter 2
● Connecting via the SIMATIC HMI HTTP protocol - Chapter 3
● Connecting via OPC - Chapter 4
● Connecting to the SIMOTION - Chapter 5
● Connecting to the WinAC - Chapter 6
● Connecting to the SIMATIC S5 - Chapter 7
● Connecting to the SIMATIC 500/505 - Chapter 8
WinCC flexible 2007 Communication Part 1
User's Manual, 07/2007, 6AV6691-1CA01-2AB0
5
Plik z chomika:
romen22
Inne pliki z tego folderu:
broszura_WinCC_flexible_2007.pdf
(4008 KB)
Siemens_Simatic_WinCC_DataMonitor_v7.0.rar
(100846 KB)
simatic wincc flexible simulator.msi
(2811 KB)
Runtime_User_Manual_en-US(1).pdf
(1172 KB)
53865269899_en-US.pdf
(21388 KB)
Inne foldery tego chomika:
hmi
logo
profinet
s5
s7
Zgłoś jeśli
naruszono regulamin