ET200_e.pdf

Important information, Table of

Contents

System Overview

Procedure - From Planning to

Initial Operation

Routing Cables and Bus

Connectors

SIMATIC S5

RS 485 Repeaters

ET 200

Distributed I/O System

IM 308-C and Memory Card –

Structure and Functioning

IM 308-C – Addressing, Access

to the Distributed I/Os and

Diagnostics

Manual

IM 308-C – Using the FB IM308C

(FB 192)

IM 308-C – Starting ET 200

S5-95U with DP Master Interface:

Design and Method of Operation

S5-95U – Addressing,

Diagnostics, FB 230

S5-95U – Starting ET 200

COM PROFIBUS Manual

(Placeholder)

A to

Appendices

Glossary, Index

EWA 4NEB 780 6000-02c

Edition 04

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as

well as to protect the product and connected equipment. These notices are highlighted in the

manual by a warning triangle and are marked as follows according to the level of danger:

Danger

indicates that death, severe personal injury or substantial property damage will result if proper

precautions are not taken.

Warning

indicates that death, severe personal injury or substantial property damage can result if proper

precautions are not taken.

Caution

indicates that minor personal injury or property damage can result if proper precautions are not taken.

Note

draws your attention to particularly important information on the product, handling the product, or

to a particular part of the documentation.

Qualified Personnel

The device/system may only be set up and operated in conjunction with this manual.

Only qualified personnel should be allowed to install and work on this equipment. Qualified

persons are defined as persons who are authorized to commission, to ground, and to tag circuits,

equipment, and systems in accordance with established safety practices and standards.

Correct Usage

Note the following:

Warning

This device and its components may only be used for the applications described in the catalog or the

technical description, and only in connection with devices or components from other manufacturers

which have been approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed

correctly, and operated and maintained as recommended.

Trademarks

SIMATIC

and SINEC

are registered trademarks of SIEMENS AG.

Some of the other designations used in these documents are also registered trademarks; the own-

er’s rights may be violated if they are used be third parties for their own purposes.

The reproduction, transmission or use of this document or its contents is not

permitted without express written authority. Offenders will be liable for

damages. All rights, including rights created by patent grant or registration of

a utility model or design, are reserved.

Disclaimer of Liability

We have checked the contents of this manual for agreement with the hard-

ware and software described. Since deviations cannot be precluded entirely,

we cannot guarantee full agreement. However, the data in this manual are

reviewed regularly and any necessary corrections included in subsequent

editions. Suggestions for improvement are welcomed.

Technical data subject to change.

Siemens AG 1995

Siemens AG

Automation and Drives (A&D)

I ndustrial Automation Systems (AS)

Postfach 4848, D- 90327 Nürnberg

Siemens Aktiengesellschaft

Order No. 6ES5 998-3ES22

ET 200 Distributed I/O System

EWA 4NEB 780 6000 02

Important Information

Purpose of the

manual

The information in this manual will enable you to:

set up the PROFIBUS bus

operate the IM 308-C as DP master and/or DP slave

parameterize the standard function block FB IM308C for the IM 308-C

operate the S5-95U with DP master interface on the PROFIBUS-DP

start up the PROFIBUS.

This manual deals with the S5-95U programmable controller and

supplements the system manual S5-90U/S5-95U Programmable Controller . It

describes all the functions and features of the DP master interface of the

S5-95U.

The COM PROFIBUS configuration software as of version V5.0 is not des-

cribed in this manual. There is a separate manual for COM PROFIBUS. The

COM PROFIBUS manual is available on the COM PROFIBUS CD-ROM.

Target group

This manual is aimed at readers who want to plan, set up and commission the

ET 200 distributed I/O system with COM PROFIBUS. We assume that you

have experience with or knowledge of how to handle the S5-95U, S5-115U,

S5-135U and S5-155U programmable controllers, depending on the master

you are using.

ET 200 Distributed I/O System

EWA 4NEB 780 6000-02c

iii

Important Information

Scope of validity

This manual is valid for the following:

Module / software

Order number

As of release/

version

IM 308-C

6ES5 308-3UC11

S5-95U

6ES5 095-8ME01

COM PROFIBUS

6ES5 895-6SE.2

3.3

6ES5 895-6SE03

RS 485 repeater

6ES7 972-0AA01-0XA0

PROFIBUS bus connectors

6ES7 972-0B.11-0XA0

6ES7 972-0B.40-0XA0

6ES7 972-0BA30-0XA0

FB IM308C (FB 192) with

demo program

Available on the intranet

(Siemens) or Internet

This manual describes all the modules approved at the time of issue. We re-

serve the right to enclose a Product Information Sheet containing up-to-date

information with each new or revised module.

Changes since the

previous version

The following things have changed since the previous version of the manual:

COM PROFIBUS as of version V 5.0 is now an open configuration soft-

ware package for DP masters and is marketed as a separate product.

COM PROFIBUS is therefore no longer described in this manual. There

is a separate manual for COM PROFIBUS, which is shipped together with

COM PROFIBUS on CD-ROM.

For a limited transitional period, COM PROFIBUS version 3.3 will be

supplied in parallel with the new version 5.0. You will still find the des-

cription of COM PROFIBUS V 3.3 in Appendix G of this manual.

The description of the optical PROFIBUS-DP network has been included.

The PROFIBUS Terminator (active bus terminating element) has been

added to the PROFIBUS network components.

Standards,

certificates and

approvals

The components described in this manual fulfill the requirements and criteria

of IEC 1131, Part 2 and the requirements for CE marking. CSA, UL and FM

certificates and approvals have been obtained. You will find detailed infor-

mation on the certificates, approvals and standards in Section A.1.

The IM 308-C master interface module and the DP master interface of the

S5-95U are based on the EN 50170, Volume 2, PROFIBUS standard.

ET 200 Distributed I/O System

EWA 4NEB 780 6000-02c

Important Information

Recycling and

disposal

The ET 200 is low in contaminants and can thus be recycled.

To recycle and dispose of your old device in an environment-friendly man-

ner, please contact:

Siemens Aktiengesellschaft

Anlagenbau und Technische Dienstleistungen

ATD ERC Essen Recycling/Remarketing

Frohnhauser Str. 69

45127 Essen

Phone: +49 201 / 816 1540 (hotline)

Fax: +49 201 / 816 1504

Other requisite

manuals

You will find information on the S5-95U with DP-master interface and all

other versions of the S5-95U in the system manual S5-90U/S5-95U Program-

mable Controller. At various points in this manual, you will find references to

the system manual S5-90U/S5-95U Programmable Controller .

The description of the slaves does not form part of this manual. You can find

the order numbers for the slave manuals in Catalog ST PI, PROFIBUS &

AS-Interface, Components on the Field Bus.

COM PROFIBUS as of version 5.0 is not described in this manual. You can

print out the COM PROFIBUS manual from the COM PROFIBUS CD-ROM

(6ES5 895-6SE03) and insert it in Chapter 12 (which is a placeholder).

Quick access

A number of features in this manual will help you to obtain quick access to

the information you require:

At the start of the manual, you will find a general table of contents, plus a

list of all the illustrations and a list of all the tables in the manual.

On each page throughout the manual, the bold-face headings on the left

summarize the contents of the individual passages.

The Appendices are followed by a Glossary containing definitions of the

important terms used in the manual.

The manual closes with an index. The index is in alphabetical order and

you can use it to find information on the topic of your choice.

ET 200 Distributed I/O System

EWA 4NEB 780 6000-02c

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: