sr6.pdf

(674 KB) Pobierz
679905524 UNPDF
The Stinson Reliant SR-6
An exact replica of a famous plane -- a model that will fly with the
same fine performance of the ship after which it's patterned!
That's what you model builders say you want, and here it is in the
Stinson Reliant SR-6. To make sure you won't go wrong, we give
you nine full pages of plans, so follow Mr. Winter's directions and
you'll have a fine craft suitable not only for flying but for parlor
display as well. Go to it!
By William Winter
Here's Mr. Winter's SR-6 fitted with flying prop and all tuned for a fast R.O.G.! Contact ! And now run
your eye over its big brother, the real Stinson Reliant, pictured at the bottom of the page. You'll find
that every detail of the model will "gee" with its counterpart.
This is the prototype of our feature model - the 1935 Stinson Reliant. It's powered with the 260 hp.
Lycoming engine and is equipped with Smith controllable prop multiple disc wheel brakes. duel
ignition magneto, and other A-1 aero apparatus. All told, the four-place SR-6 rates tops!
THIS latest Reliant, like its predecessors,
vaunts beauty, strength, and enduring
performance. Indeed the Reliant type has been
so successful that more than 260 of them have
679905524.001.png 679905524.002.png
been sold since June, 1933. Moreover, the
Lycoming motor has been used in more than 600
Stinsons, and it is estimated that this faithful
power plant has a record of 80,000,000 miles!
With the 260 h.p. motor the SR-6 cruises
at 133 m.p.h. The ship comes equipped with
Smith controllable propeller, dual ignition
magneto and multiple disc wheel brakes, besides
other more conventional fixtures. In addition to
the pilot the plane carries three passengers, 60
gallons of gas, 5 gallons of oil, baggage, and 80
lbs. of special equipment. With this load, the
Stinson climbs 875 ft. per min., has a range of
500 miles, and lands in 225 ft. with the aid of wing
flaps.
Our model, like all Stinsons, can be relied
on to give abnormally long flights, and its beauty
is only matched by its stability in flight.
is followed so that the stringers will not be "wavy"
in appearance. The top fairing is done in like
manner. The side fairing runs back as far as the
third cross piece. T1, B1, and S1 form a perfect
circle. The short upper stringers between T1 and
T2 are inserted in place and require no notches.
There are two doors, one on each side of the
body. Block E is cut to shape from soft, balsa,
sanded and cemented flush with the front edges
of T4.
To cover, use separate pieces of tissue for
the flat portion of each side. Narrow strips of
tissue will have to be cut so that the fairing may
be covered in a ship-shape manner. As each strip
is doped in place, the edges will have to be
repeatedly trimmed. The finished covering is
evenly sprayed and given a smooth coat of clear
dope. The windows are covered with cellophane.
The edges of the windows and of the doors are
painted black with a fine brush.
FUSELAGE
NOTE before beginning construction that a
full list of materials is given at the close of this
article. Incidentally, if you do not wish to mar your
magazine, make tracings of the plans on any
semi-transparent paper.
First, fasten the longerons of 3/32" to the
bench on top of the side layouts. Cut all the cross
pieces shown in that plan and cement them in
place. When dry, remove the finished sides from
the form and separate them from each other with
a double edged razor blade. Cut all the cross
pieces shown in the top view, and by the use of
pins to hold the work in position connect the two
sides at the widest points. When dry, fasten the
remaining cross pieces in place and carefully
check the alignment. It will be noted that the
rudder post of 1/8" by 3/16" is attached so that its
greatest dimension is crosswise on the fuselage.
It is best to bend the rear hook of .028 music wire
and to fasten it in position at this stage of
construction. It is necessary to crack and cement
the longerons at the front of the fuselage, as
shown in the top view, to attain the necessary
shape. All fairing formers are cut from 1/32" sheet
balsa. The notches should not be cut until the
formers are in position and you are ready to
fasten the stringers in place. All the formers are
marked as follows: Top - T, Side - S, and Bottom
- B. After the formers have been cut to shape,
those on the bottom should be glued in place.
The stringers of 1/16" sq. should now be attached
at the positions shown. This order of construction
LANDING GEAR AND TAIL WHEEL
THE fillet blocks shown on the front and
side views are cut to shape from soft balsa 3/4"
by 7/8" by 2-1/4" and sanded smooth. When
finished, glue them firmly in place as designated.
Note the holes made to receive the bamboo pins.
The struts are cut to the dimensions required and
streamlined from blocks of hard balsa 3/8" by 1-
3/8" by 3-7/8". Cut the holes shown on the detail
for the bamboo pegs. The pants are built up in
three layers. The outside ones are 3/16" sheet.
The center one is a block 2-15/16" by 9/16" by 1-
3/16". The shaping is not done until the three
plies have been firmly glued up. The 1-1/2"
wheels rotate on short .028 axles and are
mounted in the pants at the position shown. The
struts are fastened to the pants and to the fillets
with bamboo pins and with cement. The joint at
the pants is braced with two pieces of .014 music
wire as shown and bound with thread. The
complete joint is evenly glued. The joint at the
fillet is braced in like manner but with one piece of
wire.
Streamline a small piece of balsa of the
size shown in the tail wheel mounting (side view)
and cement it to the fuselage at B9. The 5/8"
wheel is mounted on a small piece of .014 wire.
This wire runs upward through the small balsa
piece and is secured in the 1/8" by 1/4" that forms
the hook mounting.
TAIL ASSEMBLY
THE stabilizer halves and the rudder are
laid out directly on the plans or tracings. Provision
is made for movable controls - if they are desired.
Sheet aluminum of a very light gauge is used for
hinges, serving the purpose well and avoiding
tedious work. The spars are 1/16" by 3/16". The
cross pieces are all cut from 1/32" sheet using the
patterns given. The edges are of 1/16" bamboo
and are bent around a candle flame to the
required shape. Pins are stuck in the bench to
hold the bamboo in position until the cement has
set.
Cover each side of all surfaces with
individual pieces of tissue. If you are building the
movable controls, the hinges should be cut to
size and attached at the proper positions. Be sure
that the aluminum is thin enough to permit free
movement of the controls. Dope the finished
surfaces lightly and smooth all the edges with
dope.
The tail fillets are cut from soft balsa 2-3/4"
by 7/8" by 9/16" and sanded smooth. They are
attached directly to the sides of the fuselage at
the position shown on the side view. The
stabilizer halves are cemented to the fillets. The
rudder or fin is attached to the fuselage on the
center stringer. The tail braces of 1/16" by 1/8"
are cut to the required length and cemented in
place (as shown on the different views).
and flush with the top of the longerons, then firmly
cemented. The aileron and flap spars are 1/8" by
3/16", are rounded as shown in the wing sections,
and are then cemented into position. The tips are
of 1/16" sq. bamboo bent to the required shape
around a candle flame. The trailing edges are
shaped from 1/16" by 3/16" stock.
To cove, use a separate piece of tissue for
each side of both left and right wing panels, flaps,
and controls. Trim all edges with care, and dope
all frayed edges smooth.
The panels are next forced on the bamboo
pins and cemented in place. Stiff paper fillet
covers are cut to the shape required by your
particular job and cemented to the fuselage along
the outermost stringer and to the fillet block at the
position designated in the top plan. The front wing
brace is cut to the given size and streamlined
from a piece of 1/8" by 1/4". The rear brace or
strut is taken from the remainder of the 1/16" by
3/16" trailing edge stock. All the struts run from
the landing gear fillet upward and rearward to the
wing spars. Small N struts of 1/16" by 1/8" are cut
to the given lengths and assembled at the
designated positions.
COWLING, PROPELLER, AND MOTOR
THE cowling is built up as shown on the
top view from sheet balsa discs. They are marked
out with a compass and glued up. The front three
are 1/4” sheet and are also cut out to the correct
diameter in the center to receive the removable
motor or plug. The fourth also is 1/4" sheet but
has only the square hole cut to receive the plug.
The remaining three sheets are 3/16" in thickness
and are cut out to the various internal sizes
required. After the whole unit has bears glued up
and dried, it is shaped with a blade sliver and
neatly sanded with fine paper. The completed unit
is cemented against the front of the fuselage. The
crankcase is shaped, as shown, from a block 1-
1/16" sq. and 3/4" thick. The nine cylinders are
cut from rounded 3/8" stock or are built up of
paper discs of alternate sizes. They are well
cemented to the crankcase. The square section
shown at the rear of the plug is 1/4" thick and
permits use of the motor as a removable plug.
The small blocks shown on the cowling in our
photo of the real plane cover the rocker arm
housings. They can be cut to shape from balsa
scraps you have at hand.
WINGS
WINGS are laid out on the drawings
preparatory to assembly. The ribs, and flap
sections are cut from 1/32" sheet with the
exception of the end pieces of the movable
sections. These latter pieces are cut from 1/16"
sheet balsa. The leading edge of 1/8" sq. is
shaped and glued in place. Check its alignment
carefully from above and from the front. The
auxiliary spar for mounting the ailerons and wing
flaps is 1/16" by 1/4" and is cemented in place as
directed in the wing drawings. The fillet blocks are
shaped from soft balsa 5" by 1-9/32" by 1-7/32".
The longest edge, as shown in the detail, is
similar to the wing section and is attached with
cement directly to the first, rib. The shorter edge
is drilled to receive the bamboo hold-on pegs that
run through the fuselage. These pegs are shown
clearly in both the front and top views. They are
inserted in position against the adjacent formers
The propeller blank is cut as shown from a
block 9" by 1-3/4" by 13/16". The carving is done
in the usual manner. The finished blades are
smoothed with fine sandpaper. If good
performance is expected, the balancing should be
done with precision. Using the pattern given, cut
two bearings from tin sheet and bend the points
to sink in the wood. Fasten one bearing to the
front of the plug and the other to the rear of the
prop hub. A loose washer is placed on the shaft
between the plug and the prop.
The motive power is 8 strands of 1/8" flat
rubber and should be lubricated whether or not a
winder is being used. An even mixture of green
soap and glycerine is suitable for lubrication and
can be procured in any drug store. Mix only a
minute quantity. If brown rubber is used, have the
motor slightly tighter.
MATERIALS required are as follows: Six
3/32" sq. by 36" balsa for longerons; four 1/16"
sq. by 36" balsa for stringers; two 1/16" by 3/16"
by 24" balsa for trailing edges, stabilizer, and
rudder spars; one 1/16" by 1/4" by 24" balsa for
aileron and flap attachment spars; one 1/8" by
3/16" by 24" balsa for aileron and flap hinge
spars; one 1/8" sq. by 30" balsa for leading edge;
one 1/8" by 1/4" by 18" balsa for wing struts; one
1/16" by 3/16" by 18" hard balsa for wing struts;
one 1/32" by 2" sheet balsa for all formers wing
and tail ribs; one 1/16" by 2" by 6" sheet balsa for
special control ribs; one 1/16" by 1/8" by 9" balsa
for N struts; two 5" by 1-9/32" by 1-7/32" soft
balsa for wing fillet blocks ; two 2-3/4" by 7/8" by
9/16" soft balsa for stabilizer fillets; two 3/4" by
7/8" by 2-1/4" soft balsa for landing gear fillet
blocks; two 3/8" by 1-3/8" by 3-7/8" hard balsa for
landing gear struts; four 2-15/16" by 3/16" by 1-
3/16" soft balsa for wheel pants ; two 2-15/16" by
9/16" by 1-3/16" soft balsa for wheel pants; one
1/4" by 3" by 10" soft balsa for cowling ; one 3/16"
by 9" by 3" soft balsa for cowling; one 1-1/16" sq.
by 3/4" soft balsa for crankcase; one 9" by 13/16"
by 1-3/4" medium balsa for propeller; one 3/8" sq.
by 5" soft balsa for cylinders; one 3" by 1-1/8" by
1/2" soft balsa for windshield peak block; and one
5/8" sq. by 1/4" soft balsa for plug holder.
Miscellaneous: one 1-oz. cement; one
2-oz. clear dope; two sheets Jap tissue; 1 ft. .028
music wire; one 6" .014 music wire; three 1/16"
by 1/4" by 12" bamboo; one scrap cellophane; 9
ft. of 1/8" flat rubber; 1 pair 1-1/2" wheels ; and
one 5/8" tail wheel.
FLYING THE MODEL
TEST your Stinson over deep grass. If
none is available, fly the ship on a few turns
R.O.G. As the proper balance is ascertained, the
number of turns are increased. The movable
controls help to balance the model, but if their
movement is more than 1/4", use small lead
weights for balancing. If the controls are used too
severely, the model will be erratic as soon as the
motor is wound out: Don't be indifferent on this
point but make the most of your labor. The
Stinson Reliant will fly any distance up to 400 ft. -
if a winder is used.
BILL OP MATERIALS
Scanned From Dec. 1935
Flying Aces
679905524.003.png
Zgłoś jeśli naruszono regulamin