X-type bluetooth.pdf

BLUETOOTH ® IN-CAR TELEPHONE

QUICK REFERENCE GUIDE

Publication Part No. JJM 10 50 99 551

Published February 2005 by Technical Communications, Jaguar Cars Limited

Quick Overview

Quick Ove rview

INTRODUCTION

Bluetooth communication operates

between bluetooth equipped devices; in

this case, the Jaguar Touch-screen

System or Audio System and a mobile

phone.

There are a limmited number of mobile

phones (currently ten) that have been

tested and proved to function correctly

with the Jaguar system - ask your Jaguar

Dealer for details.

Before any phone can operate with the

Jaguar system, it must be Paired with the

system.

This involves the phone and the Jaguar

system communicating a unique code

between them, at initiation, so that in

future they each recognise one another.

When Pairing any phone with the Jaguar

system make sure that the phone is

switched on, the phone battery is fully

charged and the User's Handbook for the

phone is available.

For specific details, consult your Jaguar

Bluetooth In-Car Telephone Handbook.

This Quick Guide describes the

Touch-screen System first ( Page 2 ),

followed by the Audio System display

( Page 6 ).

The Bluetooth system is identical for both

the Touch-screen and the Audio displays,

the difference is only in the way that the

information is presented to the user.

TOUCH-SCREEN SYSTEM

Icons and buttons used in the following

Touch-screen instructions:

Phone Mode button, to

manually select the phone

mode. Located to the left of the

Touch-screen.

Send/End icon. Located on the

Touch-screen.

Switching ON the ignition

Each time the ignition is switched on, the

following screens may be displayed.

This screen may be displayed for a few

seconds while the system is performing a

self-check.

Do not take any action. However, should

the screen stay on for longer than twenty

seconds, switch the ignition OFF and wait

for at least 6 minutes. Refer to the Jaguar

Bluetooth In-Car Telephone handbook

and Supplement.

After the brief system check, you should

see the following screen:

Quick Overview

This screen will be displayed to indicate

one of two possible conditions:

1. There is no phone currently Paired to

the vehicle system or no phone is

available. Should this be the case, this

screen will continue to be displayed

while the system is in phone mode

(the system may display the Discover

Me screen ready for you to Pair your

Bluetooth mobile phone).

2. Displayed only for a few seconds if a

phone IS Paired, but whilst the system

is booting-up and looking for a Paired

device. If the last Paired phone is

available and switched on in

Bluetooth mode, then the screen

changes from No BT Phone to Phone

Connected .

Use the touch-screen keypad to enter the

following digit sequence and press the

green Send/End icon.

##3#*# (Recommended)

The following sequence performs exactly

the same function, but times-out after

approximately five minutes, ##1#*# .

(If you are not familiar with the Pairing

process, this sequence is NOT

recommended, because of the time-out

period.)

The display will then show the following

screen.

Pairing your phone

The following instructions describe how

to initiate Pairing your mobile phone to the

Jaguar system.

If there is no mobile phone Paired to the

vehicle system and the No BT Phone

screen is displayed, Pairing may be

performed as follows:

Select Phone Mode (if not already

selected).

At the Discover Me screen the vehicle

system is waiting for communication with

a Bluetooth equipped telephone.

Quick Overview

Check that your mobile phone is set to the

Jaguar Bluetooth system, using the menu

functions on the phone. Refer to the

handbook that was supplied with your

specific mobile phone.

When Jaguar device is found on the

mobile phone display, the phone will

prompt you to enter the pass key (1313)

on the mobile phone keypad.

When the above operation has been

completed and the phone is successfully

Paired and connected with the vehicle

system, the Phone Connected screen

will be displayed.

The following process will only work with

specific phones. The phone must be ON

and already Paired with the Jaguar

system.

Note: The screen may briefly change from

Discover Me to No BT Phone whilst the

system connects the Bluetooth link,

before the Phone Connected screen is

displayed.

1. Press the vehicle Phone Mode button.

(If not already in phone mode.)

2. Use the touch-screen keypad to enter

the key sequence ##2#*# , followed by

the green, Send/End icon on the

screen.

3. To use or access your phonebook

immediately after Pairing:

Switch OFF the ignition for 6 minutes,

to allow the vehicle Bluetooth system

to complete the download process.

4. Switch ON the ignition.

The download should now have

completed successfully.

Note: Should you not wish to switch off

the ignition for 6 minutes at this time, the

phone book will be displayed after the

next normal ignition off cycle that elapses

for that duration.

Downloading your phonebook entries

The Phonebook entries on your mobile

phone can be downloaded from your

phone to the vehicle system, dependent

on the capability of the mobile phone.

For more information, refer to the specific

Quick Guide (available from your Jaguar

Dealer or Authorised Repairer) for your

phone.

Reason for Ignition OFF for 6 Minutes

The Bluetooth phone module in the

vehicle remains active for 6 minutes after

the ignition has been switched off.

Quick Overview

It is important to wait this 6 minutes so

that a clean boot-up of the Bluetooth

module is achieved and the correct

information is stored.

Once a phone has been Paired with the

vehicle system, it will not need to be done

again unless the vehicle battery is

disconnected, or possibly if the system

closes down for security reasons, or if you

choose to Pair a different phone with the

system - only one phone at any time can

be Paired with the system.

Press the green Send/End icon to initiate

the Pairing process again and to overwrite

the previously Paired phone.

Then, refer to Page 3 at the Discover Me

screen.

If the screen displays - Registered

If the ignition is switched to Accessory or

to the ON position for a short period of

time, then switched OFF and ON again,

the message displayed subsequently may

change to Registered (instead of

Discover Me or No BT Phone or Phone

Connected).

This is not due to a fault. It is because the

system has sensed an incorrect

shut-down of the Bluetooth module - that

is, it has not been allowed to follow its

normal closing down procedure time of

6minutes.

However, the state of the five bars still

indicates the correct (current) status of

the system. You can still Pair a phone to

the system and use the system as normal.

When the system changes from one

mode to another (for example, Discover

Me to Phone connected) the Registered

message will disappear.

To pair a different phone with the

system

If you attempt to Pair a different phone

immediately after switching ON the

ignition and the last Paired phone is NOT

available, you will have 2 minutes within

which to enter the the digit sequence

##3#*# to put the system into Discover

Me mode.

This is because, when the ignition is

switched ON, the system is looking for the

last Paired phone and if it does not find it

the system will revert to the Handset in

Use screen.

To Pair a different phone, select Phone

Mode and use the keypad to enter the

following digit sequence ##3#*# .

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: