Standard unlock procedure for P2K models
1. Power on the Smart-Clip from power adapter and E/G indicator will light green.
2. Power on the phone without SIM card and flash card (if present).
3. Connect the phone to Smart-Clip and press the "Unlock" button (red on older Clips).
4. E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
5. E/G will light green on success or red on error.
6. Successful unlock resets User Code to 1234, Security Code to 000000.
· Pinout P2K to USB A Standard Cable
· Pinout P2K to USB A Forced Boot Mode Cable (Repair cable)
V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking note
Unlocking newer versions of V18x/V22x/C65x/C38x/E375/E378i or C975/C980/V980/E1000 (Boot Loader 0.6.1.2) may require additional user intervention.
It may happen that E/G led still blinks after display turns off � it means that you have to turn the phone ON manually within 2-3 seconds after display turns off; alternatively you can try to unlock these newer versions of V18x/V22x/C65x/C38x/E375/E378i with battery charger on.
Unlock procedure for A920/A925/A1000
1. Power the phone on.
2. Connect the phone to a powered Clip. Phone display should give "USB cable connected" message.
3. Press UNLOCK button on the Clip.
4. Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
5. Press 1 and 2 keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these two keys during "Waiting for PST" message, the Clip will give red E/G led and you will have to start with step 1 again).
6. After 1 and 2 keys have been pressed E/G green led will blink and the phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
7. Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
8. Green E/G led glows. The cell phone is unlocked.
Axxx/Exxx/Vxxx unlocking note
Don't unplug cable right after phone reboot, wait until E/G led stops blinking!
C975/E396/E398/E1000/V635/V980 unlocking note
Remove flash card from phone before unlocking.
SE J100/C115/C116/C117/C118/C139/C140/C155/C156/E365/V170/V171 unlocking procedure
1. Power off the phone.
2. Connect the Clip to the phone using RJ45 cable (see pinout schematic below).
3. Press UNLOCK button.
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on the Clip. RX/TX leds will blink.
5. E/G led will glow green on success.*
* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times).
· Pinout SE J100
· Pinout C1xx, V1xx
· Pinout E365
Chi Mei unlocking procedure
MPx200
1. Connect S-Card and launch SmartMoto.
2. Select "Computer COM ports" in connection window.
3. Log to "Chi Mei" tab.
4. Power the phone OFF.
5. Press and hold "Leftwards" button.
6. Connect USB data cable.
7. Release "Leftwards" button.
8. Select an appropriate COM port in SmartMoto (usually is the highest number).
9. Press "Read codes" button.
10. Codes are calculated.
11. Disconnect the handset.
12. Power ON the phone with any sim card inserted.
13. Phones menu will popup with unlock code request.
14. Enter the code that was read by SmartMoto with the status "Activated".
15. Phone unlocked.
MPx220
1. Connect S-Card and launch SmartMoto..
4. Power the phone OFF and remove the battery.
5. Connect USB data cable (not a Forced Boot Mode cable!!!).
6. Select an appropriate COM port in SmartMoto (usually is the highest number).
7. Press "Read codes" button.
8. Codes are calculated.
9. Disconnect the handset.
10. Power ON the phone with any sim card inserted.
11. Phones menu will popup with unlock code request.
12. Enter the code that was read by SmartMoto with the status "Activated".
13. Phone unlocked.
Other Chi Mei models
1. Connect* powered OFF phone to PC COM port.
2. Connect S-Card and launch SmartMoto.
3. Select "Computer COM ports" in Phone connection window.
4. Log to "Chi Mei" tab.
5. Select an appropriate COM port in SmartMoto.
6. Pick the required model from the list of supported.
7. Press "Unlock" button.
8. Press "Power ON" button on the phone, as soon as SmartMoto indicates an appropriate message.
9. SmartMoto performs the Unlock process.
10. The handset is unlocked.
Note. Please do not use any HUB or extension cable. Connect the handsets to PC USB port directly using an original data USB cable. MPx models require a driver to be installed. Universal driver for all models is available within SmartMoto directory (SmartMoto install folder \drivers\…). To install the driver: connect your handset to the PC, system will detect a new device, locate the driver and run the installation as many times as system will require it.
* Chi Mei models require to be connected to PC COM port via original COM data cable or using any COM port emulator.
Chi Mei data cable pinouts.
· W220, C168, C168i
· V690, V872, V878
Sony Ericsson J110i, J120, J132, T250i, T303, Z250i, Z320i unlock procedure
1. Connect* powered OFF phone to PC.
2. Connect S-Card to PC USB port and launch SmartMoto.
4. Log to "SE phones" tab.
6. Select required model from the list.
* SE models require to be connected to PC COM port via original COM data cable or using any COM port emulator.
· J1xxi cable pinout
· T250i, T303, Z250i, Z320i cable pinout
· J132 cable pinout
Compal ("Calypso+" based) models unlock procedure
C257, C261, F3, V175, V176, V177, W161, W181, W205, W206, W208, W209, W213, W215, W218, W370, W375, W375B, W377
2. Launch SmartMoto.
4. Log to "Compal" tab.
6. Press "Unlock" button.
7. Press "Power ON" button on the phone, as soon as SmartMoto indicates an appropriate message.
8. SmartMoto performs the Unlock process.
9. The handset is unlocked.
* Compal models require to be connected to PC COM port via original COM data cable or using any COM port emulator.
· Compal ("Calypso+" based) data cable pinout.
· Cable for Motofone F3.
Compal ("Locosto" based) models unlock procedure
W156, W160, W175, W177, W180, W230, W270, W360, W388, W396, W450, ZN200
For unlock purposes the models W156, W160, W175, W177, W180, W230, W270, W360, W388, W450 require to be connected to PC USB port.
1. Connect S-Card and Mini USB data cable to PC USB port and launch SmartMoto.
2. Select "Computer COM ports" in Phone connection area.
3. Log to the tab "Compal models"
4. Choose an appropriate model from the list.
5. Press Unlock button.
6. SmartMoto will inform "Connect phone to computer USB port before proceeding".
7. Connect data cable to the powered OFF phone with inserted battery.
8. The SmartMoto will automatically (no user intervention is required during the installation) install "Locosto flash interface" driver and display the following message: "reconnect phone and try again".
9. Disconnect data cable from the phone, remove and insert the battery back to the phone.
10. Connect data cable and press Unlock again.
11. The unlock process continues.
12. Message "Unlock ok" informs that process is finished and the phone can be disconnected.
NOTEFor unlock purposes the only driver that is required is the "Locosto flash interface" driver. No need to install the phone W156, W160, W175, W180, W230, W270, W360, W388 model driver.
Service functions for Compal models
· Repair EEPROM � this option has to be used when it�s required to perform repair of the corrupted parts of the existing EEPROM in the phone.
· Use default EEPROM (for repair only) � this option allows writing new EEPROM zone to the phone and recalculating it according to the phone parameters.
· Format FFS � format file system. Resets all user settings to the default value and removes all user data.
Motofone F3 pinout
· Motofone F3 pinout
Motofone F3 Unlock Clip
F3 Unlock Clip � is the easiest unlock solution, available on the market yet. It is operated by one button and requires to be powered from mains adapter or even 9V battery.
F3 unlock procedure description
1. Connect power to F3 Unlock Clip (9V battery can be used).
2. Connect F3UC to the handset, powered on or switched into boot mode*.
3. Press Unlock button on the clip.
4. LED on the clip starts to blink frequently. Unlock process is in progress.
5. On successful unlock, LED stops blinking and lights up for about 10 seconds.
*To switch F3 into boot mode, please power off the phone and press 3 keys combination: *#Power On. The handset display will remain blank.
NOTEIf the LED on F3 Unlock Clip, after frequent blinking starts to blink slower instead of lighting up � the unlock process failed. Please disconnect the phone from the cable, remove and insert the battery, switch the phone to boot mode and perform unlock again.
Remove RSA
Some handsets require Remove RSA procedure to be performed before actual Smart-Clip unlocking. Remove RSA procedure itself � it�s a partial flashing of the phone firmware.
Unlockin...
lysy112