DRIVE SHAFT & PROPELLER SHAFT.pdf

30–1

DRIVE SHAFT / PROPELLER SHAFT

–

DRIVE SHAFT, PROPELLER SHAFT, AXLE

PROBLEM SYMPTOMS TABLE

Use the table below to help you find the cause of the problem. The numbers indicate the priority of

the likely cause of the problem. Check each part in order. If necessary, replace these parts.

3005C–02

Symptom

Suspect Area

See page

5. Wheel

6. Front wheel alignment

7. Rear wheel alignment

8. Hub bearing (Worn)

9. Front shock absorber

10.Rear shock absorber

28–1

26–6

27–4

30–2

26–10

27–8

Wander

1. Wheel (Imbalance)

2. Hub bearing (Worn)

3. Lower suspension arm

28–1

30–2

26–16

26–21

26–24

26–10

ATM:

Front wheel shimmy

4. Lower suspension arm

MTM:

5. Lower ball joint (Worm)

6. Front shock absorber

1. Front drive shaft

2. Front shock absorber

3. Hub bearing (Worn)

4. Lower ball joint (Worm)

30–6

26–10

30–2

26–24

Noise (Front)

1. Hub bearing (Worn)

2. Rear shock absorber

30–2

27–8

Noise (Rear)

AVENSIS REPAIR MANUAL (RM1018E)

30–2

DRIVE SHAFT / PROPELLER SHAFT

–

DRIVE SHAFT, PROPELLER SHAFT, AXLE

3005B–02

ON–VEHICLE INSPECTION

1. INSPECT FRONT AXLE HUB BEARING BACKLASH

(a) Using a dial indicator, check the backlash near the center

of the axle hub.

Maximum: 0.05 mm (0.0020 in.)

If the backlash exceeds the maximum, replace the bearing.

D26919

2. INSPECT FRONT AXLE HUB DEVIATION

(a) Using a dial indicator, check the deviation at the surface

of the axle hub outside the hub bolt.

Maximum: 0.05 mm (0.0020 in.)

If the backlash exceeds the maximum, replace the axle hub.

D26920

3. INSPECT REAR AXLE HUB BEARING BACKLASH

(a) Using a dial indicator, check the backlash near the center

of the axle hub.

Maximum: 0.05 mm (0.0020 in.)

If the backlash exceeds the maximum, replace the axle hub as-

sembly.

C98714

4. INSPECT REAR AXLE HUB DEVIATION

(a) Using a dial indicator, check the deviation at the surface

of the axle hub outside the hub bolt.

Maximum: 0.07 mm (0.0028 in.)

If the backlash exceeds the maximum, replace the axle hub as-

sembly.

C98715

AVENSIS REPAIR MANUAL (RM1018E)

30–21

DRIVE SHAFT / PROPELLER SHAFT

–

FRONT AXLE HUB SUB–ASSY LH

COMPONENTS

30091–02

Front Stabilizer Link Assy LH

Speed Sensor Front LH

8.0 (82, 71 in.

lbf)

74 (755, 55)

Cotter Pin

19 (194, 14)

220 (2,243, 162)

Front Axle Assy LH

Front Drive Shaft

Assy LH

49 (500, 36)

102 (1,040, 75)

Tie Rod End Sub–assy LH

Front Disc

Front Disc Brake

Caliper Assy LH

Front Suspension Arm

Sub–assy Lower No. 1 LH

Front Axle

LH Hub Bolt

216 (2,200, 159)

89 (908, 66)

Front Axle Hub LH Nut

Front Axle Hub

LH Snap Ring

Steering Knuckle LH

Disc Brake Dust Cover Front LH

Front Axle Hub

LH Bearing

Cotter Pin

8.3 (85, 73 in.

lbf)

103 (1,050, 76)

Lower Ball Joint

Assy Front LH

Front Axle

Hub Sub–assy LH

8.3 (85, 73 in. lbf)

: Specified torque

m (kgf

cm, ft

lbf)

Non–reusable parts

D30592

AVENSIS REPAIR MANUAL (RM1018E)

30–22

DRIVE SHAFT / PROPELLER SHAFT

–

FRONT AXLE HUB SUB–ASSY LH

300JY–01

REPLACEMENT

HINT:

Replace the RH side by the same procedures as the LH side.

REMOVE FRONT WHEEL

SEPARATE FRONT STABILIZER LINK ASSY LH ( See page 30–6 )

REMOVE FRONT AXLE HUB LH NUT

(a)

Using SST and a hammer, unstake the staked part of the

axle hub LH nut.

SST

09930–00010

(b)

While applying the brakes, remove the axle hub LH nut.

F45751

DISCONNECT SPEED SENSOR FRONT LH

(a)

Remove the bolt, and disconnect the speed sensor wire

and flexible hose from the shock absorber.

C80291

(b) Remove the bolt, separate the speed sensor front LH

from the steering knuckle.

NOTICE:

Be careful not to damage the speed sensor.

Prevent foreign matter from attaching to the speed

sensor.

F44775

5. SEPARATE FRONT DISC BRAKE CALIPER ASSY LH

(a) Removing the 2 bolts, separate the disc brake caliper

assy LH from the steering knuckle.

NOTICE:

Use a string or other device to keep the brake caliper from

hanging down.

C67088

AVENSIS REPAIR MANUAL (RM1018E)

30–23

DRIVE SHAFT / PROPELLER SHAFT

–

FRONT AXLE HUB SUB–ASSY LH

REMOVE FRONT DISC

SEPARATE TIE ROD END SUB–ASSY LH

Turn

SST

(a)

Remove the cotter pin and nut.

(b)

Using SST, separate the tie rod end sub–assy LH from the

steering knuckle.

SST

09628–62011

Hold

F40217

SEPARATE FRONT SUSPENSION ARM SUB–ASSY

LOWER NO.1 LH

(a)

Remove the bolt and 2 nuts, and separate the suspension

arm sub–assy lower No.1 LH from the lower ball joint.

C80293

9. REMOVE FRONT AXLE ASSY LH

(a) Using a plastic hammer, separate the drive shaft assy LH

from the axle hub.

NOTICE:

Be careful not to damage the boot and ABS speed sensor

rotor.

D27403

(b)

Remove the 2 bolts, nuts and steering knuckle with the

shock absorber.

C83023

AVENSIS REPAIR MANUAL (RM1018E)

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: