Siemens Sinamics cu240e.pdf

(3248 KB) Pobierz
Operating Instructions · Edition 10/2007
Control Units
CU240E
sinamics
G120
s
791986644.043.png 791986644.044.png 791986644.045.png 791986644.046.png 791986644.001.png 791986644.002.png 791986644.003.png 791986644.004.png
1
2
3
SINAMICS
4
G120
Control Units CU240E
5
6
Operating Instructions
7
8
9
10
11
A
B
Firmware version 3.1
10/2007
A5E01301938B AA
 
791986644.005.png 791986644.006.png 791986644.007.png 791986644.008.png 791986644.009.png 791986644.010.png 791986644.011.png 791986644.012.png 791986644.013.png 791986644.014.png 791986644.015.png 791986644.016.png 791986644.017.png 791986644.018.png
 
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY
Ordernumber: A5E01301938B AA
Ⓟ 09/2007
Copyright © Siemens AG 2007.
Technical data subject to change
791986644.019.png 791986644.020.png 791986644.021.png 791986644.022.png 791986644.023.png 791986644.024.png 791986644.025.png 791986644.026.png 791986644.027.png 791986644.028.png 791986644.029.png 791986644.030.png 791986644.031.png 791986644.032.png 791986644.033.png 791986644.034.png 791986644.035.png 791986644.036.png 791986644.037.png 791986644.038.png 791986644.039.png 791986644.040.png 791986644.041.png 791986644.042.png
 
Table of contents
Introduction. ............................................................................................................................................... 7
Documents for the Inverter . ........................................................................................................... 7
Description of Document Classes. ................................................................................................. 8
Safety notes. .............................................................................................................................................. 9
Description. .............................................................................................................................................. 15
Accessories for the CU240E. ....................................................................................................... 16
Features and Functions of the CU240E . ..................................................................................... 17
Layout and Block diagram . .......................................................................................................... 19
Interfaces of the CU240E.. ........................................................................................................... 21
Factory Settings of the Control Unit. ............................................................................................ 23
Installing/Mounting. .................................................................................................................................. 25
Fitting the CU to the PM. .............................................................................................................. 25
Connecting the Control Unit via terminals . .................................................................................. 26
Frequency setpoint via terminals. ................................................................................................ 28
Connecting a CU240E via USS. .................................................................................................. 30
Installation Check List. ................................................................................................................. 30
Commissioning. ....................................................................................................................................... 31
5.1 Single Commissioning . ................................................................................................................ 32
5.2 Series Commissioning . ................................................................................................................ 33
5.2.1 Series Commissioning . ................................................................................................................ 33
5.2.2 Upload and Download of Parameter Sets . .................................................................................. 35
5.3 Common Commissioning Information. ......................................................................................... 36
5.4 Message F00395 . ........................................................................................................................ 37
5.5 Commissioning using the BOP. ................................................................................................... 38
5.5.1 Basic Operator Panel (BOP). ....................................................................................................... 38
5.5.1.1 Function Keys of the BOP. ........................................................................................................... 39
5.5.1.2 Changing Parameters via BOP. ................................................................................................... 40
5.5.2 Overview Commissioning with the BOP . ..................................................................................... 41
5.5.3 Basic Commissioning. .................................................................................................................. 42
5.5.3.1 Quick Commissioning . ................................................................................................................. 42
5.5.3.2 Motor Data Identification. ............................................................................................................. 46
5.5.3.3 Speed Control Optimization. ........................................................................................................ 47
5.5.4 Further Settings for Commissioning . ........................................................................................... 47
5.5.4.1 Calculating the Motor and Control Data.. ..................................................................................... 47
5.5.4.2 Commissioning the Application. ................................................................................................... 48
5.5.4.3 Reset Parameters to Factory Settings. ........................................................................................ 59
Series commissioning using the BOP. ......................................................................................... 61
Commissioning with STARTER. .................................................................................................. 63
Control Units CU240E
Operating Instructions, 10/2007, A5E01301938B AA
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin