b_63950en_02_v2004_07_26_152(1).pdf

FANUC Series 30*/300*/300*s-MODEL A

FANUC Series 31*/310*/310*s-MODEL A5

FANUC Series 31*/310*/310*s-MODEL A

FANUC Series 32*/320*/320*s-MODEL A

PARAMETER MANUAL

B-63950EN/02

• No part of this manual may be reproduced in any form.

• All specifications and designs are subject to change without notice.

The export of this product is subject to the authorization of the government of the country

from where the product is exported.

In this manual we have tried as much as possible to describe all the various matters.

However, we cannot describe all the matters which must not be done, or which cannot be

done, because there are so many possibilities.

Therefore, matters which are not especially described as possible in this manual should be

regarded as ”impossible”.

This manual contains the program names or device names of other companies, some of

which are registered trademarks of respective owners. However, these names are not

followed by  or  in the main body.

B-63950EN/02

DEFINITION OF WARNING, CAUTION, AND NOTE

This manual includes safety precautions for protecting the user and

preventing damage to the machine. Precautions are classified into

Warning and Caution according to their bearing on safety. Also,

supplementary information is described as a Note. Read the Warning,

Caution, and Note thoroughly before attempting to use the machine.

WARNING

Applied when there is a danger of the user being

injured or when there is a danger of both the user

being injured and the equipment being damaged if

the approved procedure is not observed.

CAUTION

Applied when there is a danger of the equipment

being damaged, if the approved procedure is not

observed.

NOTE

The Note is used to indicate supplementary

information other than Warning and Caution.

• Read this manual carefully, and store it in a safe place.

s-1

B-63950EN/02

PREFACE

Applicable models

The models covered by this manual, and their abbreviations are :

Model name

Abbreviation

FANUC Series 30 i -MODEL A

30 i –A

Series 30 i

FANUC Series 300 i -MODEL A

300 i –A

Series 300 i

FANUC Series 300 i s-MODEL A 300 i s–A

Series 300 i s

FANUC Series 31 i -MODEL A

3 1 i –A

Series 31 i

FANUC Series 31 i -MODEL A5

31 i –A5

FANUC Series 310 i -MODEL A 310 i –A

FANUC Series 310 i -MODEL A5 310 i –A5

Series 310 i

FANUC Series 310 i s-MODEL A 310 i s–A

FANUC Series 310 i s-MODEL A5 310 i s–A5

Series 310 i s

FANUC Series 32 i -MODEL A

32 i –A

Series 32 i

FANUC Series 320 i -MODEL A

320 i –A

Series 320 i

FANUC Series 320 i s-MODEL A 320 i s–A

Series 320 i s

NOTE

1 For an explanatory purpose, the following

descriptions may be used according to the types of

path control used:

- T series: For the lathe system

- M series: For the machining center system

2 Unless otherwise noted, the model names

31 i /310 i /310 i s-A, 31 i /310 i /310 i s-A5, and

32 i /320 i /320 i s-A are collectively referred to as

30 i /300 i /300 i s. However, this convention is not

necessarily observed when item 3 below is

applicable.

3 Some functions described in this manual may not

be applied to some products.

For details, refer to the DESCRIPTIONS

(B-63942EN).

p-1

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: