LQ170M1LW2AB.pdf

SPEC No.LD－19305A

ISSUE：Mar.1.2007

PAGE:23 pages

DEVICE SPECIFICATION FOR

TFT-LCD Module

MODEL No.

LQ0DZA0096

LD19305A-1

These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include

materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them

in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the

express written permission of SHARP.

In case of using the device for applications such as control and safety equipment for transportation(aircraft,

trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require

higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and

redundant system design should be taken.

Do not use the device for equipment that requires an extreme level of reliability, such as aerospace

applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or

other equipment for life support.

SHARP assumes no responsibility for any damage resulting from the use of the device which does not

comply with the instructions and the precautions specified in these specification sheets.

This specification sheets sheet is to guarantee the quality of the LCD module itself, only Should you need to

evaluate and confirm the performance of the module, please do so when the LCD module is assembled into

your finished product.

If any problem occurs in relation to the description of this specification sheets , it shall be resolved through

discussion with spirit of cooperation.

Contact and consult with a SHARP sales representative for any questions about this device.

LD19305A-2

Table of contents

1. Application

………………………………………………………………………… 3

2. Overview

………………………………………………………………………… 3

3. Mechanical Specifications ………………………………………………………………………… 3

4. Input Terminals …………………………………………………………… 4

4-1. TFT-LCD panel driving …………………………………………………………… 4

4-2. Interface block diagram …………………………………………………………… 5

4-3. Backlight driving ………………………………………………………………………… 6

5. Absolute Maximum Ratings ………………………………………………………………………… 6

6. Electrical Characteristics …………………………………………………………… 7

6-1. TFT-LCD panel driving ………………………………………………… 7

6-2. LVDS Input Specification ………………………………………………… 9

6.2.1. Switching Characteristics ………………………………………………… 9

6.2.2. LVDS Data Input Timing ………………………………………………… 10

6-3. Backlight driving ………………………………………………… 11

6.3.1.Backlight lifetime ………………………………………………… 11

6.3.2. Inverter unit driving ………………………………………………… 11

6.3.3. SMBus Protocol ………………………………………………… 12

6.3.4. Register Definition ………………………………………………… 12

6.3.5. Brightness Control ………………………………………………… 15

6.3.6. AC Characteristics (SMB_DAT,SMB_CLK) ………………………………………………… 16

7. Timing characteristics of input signals ………………………………………………… 17

7-1. Timing characteristics ………………………………………………… 17

7-2. Input Data Signals and Display Position on the screen

……………………… 18

8. Input Signals, Basic Display Colors and Gray Scale of Each Color

……………………… 19

9. Optical Characteristics

…………………………………………………………………………… 20

10. Display Quality …………………………………………………………………………… 21

11.Handling Precautions …………………………………………………………………………… 22

12.Packing form

…………………………………………………………………………… 22

Fig.1 Outline dimensions …………………………………………………………………………… 23

1. Application

LD19305A-3

These specification sheets applies to a color TFT-LCD module, LQ0DZA0096.

2. Overview

This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film

Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit

and a backlight unit. Graphics and texts can be displayed on a 1920 × 3 × 1200 dots panel with 262,144

colors by using LVDS ( L ow Vo ltage Di fferential S ignaling) to interface and supplying +3.3V DC supply

voltage for TFT-LCD panel driving and supply voltage for backlight.

Optimum viewing direction is 6 o'clock.

Backlight-driving DC/AC inverter is built in this module.

3. Mechanical Specifications

Parameter

Specifications

Unit

Display size

43(17.0") Diagonal

Active area

365.76 (H) × 228.60 (V)

Pixel format

1920 (H) × 1200 (V)

pixel

(1 pixel = R+G+B dots)

Aspect ratio

16 : 10

Pixel pitch

0.1905 (H) × 0.1905 (V)

Pixel configuration

R,G,B vertical stripe

Display mode

Normally white

Surface treatment

Anti-glare and hard-coating 5H

Low reflection

Parameter

Min.

Typ.

Max.

Unit

Unit outline dimensions

[Note 1]

Width

381.7

382.2

382.7

Height

244.0

244.5

245.0

Depth －－

7.0

Mass [Note 2]

－

730

750

[Note 1] excluding inverter unit, backlight cables and the mounting tab.

[Note 2] including inverter unit.

Outline dimensions is shown in Fig.1

LD19305A-4

4. Input Terminals

4-1. TFT-LCD panel driving

CN1 (LVDS signals and +3.3V DC power supply)

Pin No.

Symbol

Function

Remark

GND

V CC

+3.3V power supply

V CC

+3.3V power supply

V EDID

DCC+3.3V power supply

Reserved

R1IN0- Receiver signal of A side pixel (-)

[Note 1]

R1IN0+ Receiver signal of A side pixel (+)

[Note 1]

GND

R1IN1- Receiver signal of A side pixel (-)

[Note 1]

R1IN1+ Receiver signal of A side pixel (+)

[Note 1]

GND

R1IN2- Receiver signal of A side pixel (-)

[Note 1]

R1IN2+ Receiver signal of A side pixel (+)

[Note 1]

GND

CK1 IN- Clock signal of A side pixel (-)

[Note 1]

CK1 IN+ Clock signal of A side pixel (+)

[Note 1]

GND

R2IN0- Receiver signal of B side pixel (-)

[Note 1]

R2IN0+ Receiver signal of B side pixel (+)

[Note 1]

GND

R2IN0- Receiver signal of B side pixel (-)

[Note 1]

R2IN0+ Receiver signal of B side pixel (+)

[Note 1]

GND

R2IN0- Receiver signal of B side pixel (-)

[Note 1]

R2IN0+ Receiver signal of B side pixel (+)

[Note 1]

GND

CK2 IN- Clock signal of B side pixel (-)

[Note 1]

CK2 IN+ Clock signal of B side pixel (+)

[Note 1]

[Note 1] Relation between LVDS signals and actual data is shown in following section (4-2)(7-2).

[Note 2] The shielding case is connected with signal GND.

Using connector : FI-XB30SL-HF10 (JAE) or equivalent.

Corresponding connector : FI-X30M,FI-X30ML or FI-X30H (JAE)

(Sharp is not responsible to its product quality, if the user applies a connector not corresponding

to the above model.)

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: