Infinity-Box_UserManual.pdf

1.Introduction...........................................................................................................................3

1.1.General IMPORTANT information (you can skip rest info, but read this please)..................................3

1.2.Problems and support....................................................................................................................3

2.System requirements..............................................................................................................4

3.Installation.............................................................................................................................5

4.How to start...........................................................................................................................6

4.1.Insert dongle.................................................................................................................................6

4.2.Connect Box..................................................................................................................................6

4.3.Select Com Port (WinXP example)...................................................................................................6

4.4.Start software................................................................................................................................6

5.Panasonic G60/X100/A200/X500.............................................................................................7

5.1.Flashing.........................................................................................................................................7

5.2.SP-Unlock......................................................................................................................................7

5.3.UserLock.......................................................................................................................................7

5.4.Repair Imei....................................................................................................................................7

5.5.Read flash.....................................................................................................................................7

6.Panasonic X60/X66/X68/X200/X400/A500................................................................................8

6.1.Flashing.........................................................................................................................................8

6.2.SP-Unlock......................................................................................................................................8

6.3.Reset to default.............................................................................................................................8

6.4.Read flash.....................................................................................................................................8

7.Panasonic GD55/G50/G51/G70/A100/A101/A102/A210/X300/SC3.............................................9

7.1.Flashing.........................................................................................................................................9

7.2.SP-Unlock: G50/G51/G70/A100/A101/A102/X300.............................................................................9

7.3.SP-Unlock: GD55............................................................................................................................9

7.4.Reset Settings................................................................................................................................9

7.5.Lock to Network.............................................................................................................................9

7.6.Repair Imei....................................................................................................................................9

7.7.Read flash.....................................................................................................................................9

7.8.Important !....................................................................................................................................9

8.Nec N342i/E101...................................................................................................................10

8.1.Flashing.......................................................................................................................................10

8.2.SP-Unlock....................................................................................................................................10

8.3.Reset Settings..............................................................................................................................10

8.4.Lock to Network...........................................................................................................................10

8.5.Repair Imei..................................................................................................................................10

8.6.Read flash...................................................................................................................................10

8.7.Important !..................................................................................................................................10

9.Philips 568 (CT5688)............................................................................................................11

9.1.Flashing.......................................................................................................................................11

9.2.SP-Unlock....................................................................................................................................11

9.3.Lock to Network...........................................................................................................................11

9.4.Read flash...................................................................................................................................11

9.5.Important !..................................................................................................................................11

10.Bird/Fly S288/S688/S788....................................................................................................12

10.1.Flashing.....................................................................................................................................12

10.2.SP-Unlock: S288.........................................................................................................................12

10.3.SP-Unlock: S688/S788................................................................................................................12

10.4.Reset Settings/Repair “freez/restart” problem..............................................................................12

10.5.Read flash..................................................................................................................................12

11.Siemens CFX65...................................................................................................................13

11.1.Flashing.....................................................................................................................................13

11.2.SP-Unlock..................................................................................................................................13

11.3.Reset Settings/Phone Code.........................................................................................................13

11.4.Read flash..................................................................................................................................13

1. Introduction

MAIN

Main part of firmware. Other names is: MCU, Firmware.

FFS

Device file system with internal pictures/logo/melodies/WAP settings etc. Other names: FLEX, MAP.

EEPROM

Part of device memory with battery/RF calibration data, user settings etc.

1.1. General IMPORTANT information

(you can skip rest information, but read this please)

Before any operation select correct phone type, COM port and port speed.

Software can be used on ordinary COM port and with any types of high-speed com ports like USB-RS232 converters (FTDI,

Prolific) or high-speed PC card (f.e. Moxa C104/C168 etc.). It is not recommended to use any system patch to increase PC motherboard

built-in COM port speed. Some procedures that need fast flashing can be supported only with our special box/cables (FTDI based USB-

RS232 converter).

For many models it is possible to flash all parts of phone (MAIN/FFS/LP) one by one or all together. You can use any

combination. But when you flash only LP/FFS without MAIN, please, be carefull and always test phone functionality after this operation.

Fast LP/FFS flashing can save a lot of time, but if MAIN version will be not the same as version of LP/FFS then it is possible to get

different bugs in phone functionality.

So, it is recommended to use MAIN+FFS+LP flashing when possible.

Also, always use LP/FFS files that have the same version (you can easy see this by file names). Use different version FFS/LP files only in

emergency case.

It is possible to flash phones from different regions (Euro to Asian and back) but remember that it can be some limitations for

Euro/Asian flashing because some models for Asian market can have hardware difference in compare with European models.

After end of each operation always remove battery from phone for several seconds and put it back. Never leave battery in

device for long time after any operations because you see nothing on device LCD but internal procedures can still works and battery can

be empty in short time.

“ Read Flash ” option added for service use only . If you can’t find correct flash files for your phone on support area but you

have sample phone with flash that you need: read flash from it and send to support team. This readed flash file will be tested by our

high-qualified engineers and then it will be uploaded into support area. After this operation you will be able to use new flash file for

your phone. Probably this is not so easy and fast way to get new flash files for end-user, but this procedure can save a lot of your

money and avoid you to buy permanently damaged phone after wrong flashing.

Please, be patient, reading process can take a lot of time.

You can stop any current process by pressing “Stop” button but think twice before you will make this.

Never remove dongle from PC USB port when software make any operation. This action can make software freez and as a

result your phone can be damaged. If dongle was removed from PC it is need to close software and start it again when dongle will be

inserted.

1.2. Problems and support

If you have any problems with software, please, make the next operations:

Check, is dongle inserted in USB port of your PC and you can see dongle serial number at right down corner of software.

Check, is cable really working (inserted in PC, no wires is damaged).

Check, is your cable can support selected COM port speed.

Try requested operation on lower port speed. In many cases this can solve problem.

Also, it is always better to use cables with external power.

If you still have problems, please, contact to support with detailed description of problem, and, also, please, attach in you problem

description all messages from software “Operation status” window. Also, include information about your PC hardware, cable type, OS

type and dongle No (you can find it at bottom right corner of software window).

If you have found any bugs in software, please contact to support. We will be glad to help you and to remove all bugs that was found.

Sales e-mail:

support@infinity-box.com

Technical support e-mail:

support@infinity-box.biz

Language pack. Other names: LangPack, LP, PPM.

2. System requirements

PC with two free USB port for box and dongle.

OS supported: Win98SE, WinXP (WinXP prefered).

About 250Mb free disk space for program modules and drivers.

About 60Gb free disk space for flash files.

3. Installation

1. Download Drivers package: http://www.infinity-box.com/download/

2. Run Infinity-Box_Drivers_vX.X.exe

3. Read Installation manual: x:\Program Files\InfinityBox\Drivers\box\readme.rtf

4. How to start

4.1. Connect dongle to PC

If you have box with external Smart-Card reader you need to insert dongle in USB port. When you insert dongle first time, it

can be that PC ask you to select folder with Smart-Card drivers. Please, follow installation manual to install Smart-Card drivers.

4.2. Connect Box to PC

Connect Box to PC via USB cable and select COM-Port.

4.3. Select COM Port (WinXP example)

Make right mouse click on “My Computer” icon and select “Properties”.

Go to page “Hardware” and press “Device Manager” button.

Go to “Ports (COM & LPT)” section and find “Infinity USB Serial Port (COM X )”, where X is your Box COM-Port number. Use this COM-

Port No for future operation.

4.4. Start software

If dongle inserted then you will see dongle serial number and dongle firmware version in right bottom corner of window.

Serial number looks like XXXX:YYYY (where XXXX is a S/N and YYYY is a firmware version). If you see this number this means that all

Ok and you can start work.

5. Panasonic

G60/X100/A200/X500

5.1. Flashing

Check/uncheck regions that you want to flash (Main/FFS/LP)

Select files with parts of flash that you need to write

PowerOff device and connect cable

Press “Start” button and quickly press device “Power” (Red) button

5.1.1. Special options

“SafeMode”

Use this mode always when possible. When this option is checked then this can save your device after empty battery or terminated

flashing.

Use this mode un-checked if you are absolutely sure that you need to replace device boot-code.

“Connect Mode”

Ordinary this option automatically set by software. Change state of this box if you can’t connect to device in several tries.

5.2. SP-Unlock

Device have to be in PowerOn state.

Press “SP-Unlock” button and wait several seconds. Device automatically PowerOff after operation.

Insert SIM card and PowerOn device. You will be asked to enter unlock code. Enter 00000000 (eight zeroes).

5.3. UserLock

Device have to be in PowerOn state.

Press “User Code” button and wait several seconds. Device automatically PowerOff after operation.

Insert SIM card and PowerOn device. You will be asked to enter user code. Enter 0000 (four zeroes) or 1234.

5.4. Repair Imei

G60 : Device have to be in PowerOn state.

X100 : Device have to be in PowerOff state.

A200 : Device have to be in PowerOff state.

X500 : Device have to be in PowerOn state.

Enter Imei number to repair.

Press “Repair Imei” button and wait several seconds.

X500 : if you will see error message at end of this process then you must to make this:

1. PowerOff device

2. Press “Prepare” button and quickly PowerOn device

3. Wait until this operation complete

4. PowerOn device and press “Repair Imei” button again

5.5. Read flash

Device have to be in PowerOff state.

Press “Read flash” button and wait until process end.

You will find new file in the folder with software.

6. Panasonic

X60/X66/X68/X200/X400/A500

6.1. Flashing

Check/uncheck regions that you want to flash (Main/FFS/LP)

Select files with parts of flash that you need to write.

PowerOff device and connect cable

Press “Start” button and quickly press device “Power” (Red) button.

If flashing process was terminated by any reason, don’t worry. Your device alive and you can start flashing process again.

You can use X6x firmware files for the next models: X60, X66, X68

6.1.1. Special options

“Reset default”

Use this option checked to reset device user settings to factory defaults after flashing.

6.2. SP-Unlock

Device have to be in PowerOn state or in TEST-MODE.

To enter TEST MODE:

1. PowerOff device

2. Press and hold together * and # buttons

3. Press Power (Red) button and hold all three buttons several seconds.

Press “SP-Unlock” button and wait several seconds. Device automatically PowerOff after operation.

For emergency case it is possible to use “Backup before unlock” option. In this case operation takes more time.

to default

This option reset device user settings to factory defaults

Device have to be in PowerOn state.

Press “Reset to default” button and wait several seconds. Device automatically PowerOff after operation.

6.4. Read flash

Device have to be in PowerOff state.

Press “Read flash” button and wait until process end.

You will find new file in the folder with software.

6.3. Reset

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: