M30_part2(1).pdf

(637 KB) Pobierz
Microsoft Word - SM30m_4_26to49.doc
4 Replacement Procedures
4.9 Keyboard
4 Replacement Procedures
4.9 Keyboard
Removing the Keyboard
To remove the keyboard, follow the steps below and refer to figures 4-11 to 4-12.
1. Turn the computer face up and open the display panel.
2. Insert your finger into the latches between the keyboard brace and the computer, and
lift up the keyboard brace to unlatch and remove it.
3. Remove the following screw securing the keyboard and keyboard hold plates. Then
remove the keyboard hold plate .
• M2×4B BIND screw ×1
Or
• M2×4 LH STICK screw ×1
Keyboard brace
M2×4B BIND or M2×4 LH STICK
M2×4B BIND or M2×4 LH STICK
Keyboard hold plate
Figure 4-11 Removing the keyboard brace and keyboard hold plate
4-26
Satellite M30 Maintenance Manual (960-455)
721699638.009.png 721699638.010.png 721699638.011.png
4.9 Keyboard
4 Replacement Procedures
4. Lift the upper side of the keyboard out and turn it’s face down on the palm rest.
5. Remove the following screw securing the keyboard support plate and remove the
keyboard support plate.
• M2.5×8B FLAT HEAD screw ×1
M2.5×8B FLAT HEAD
Keyboard support
plate
PJ3200
Keyboard cable
Figure 4-12 Removing the keyboard support plate
7. Disconnectthe keyboard cable from the connector PJ3200 on the system board, and
remove the keyboard.
Satellite M30 Maintenance Manual (960-455)
4-27
721699638.012.png
4 Replacement Procedures
4.9 Keyboard
Installing the Keyboard
To install the keyboard, follow the steps below and refer to figures 4-11 to 4-12.
1. Place the keyboard face down on the palm rest.
2. Connect the keyboard cable to the connector PJ3200 on the system board.
3. Place the keyboard support plate and secure it with the following screw .
• M2.5×8B FLAT HEAD screw ×1
4. Turn the keyboard face up and put it on the computer. Make sure that there is no gap
between the keyboard and the computer.
5. Place the keyboard hold plates on the keyboard. Then secure the keyboard hold
plates and the keyboard with the following screws .
• M2×4B BIND screw ×2
Or
• M2×4 LH STICK screw ×2
6. Install the keyboard brace by pressing it from the topside.
4-28
Satellite M30 Maintenance Manual (960-455)
721699638.001.png
4.10 Switch cover ASSY/Switch membrane
4 Replacement Procedures
4.10 Switch cover ASSY/Switch membrane
Removing the Switch cover ASSY/Switch membrane
To remove the Switch cover ASSY/Switch membrane, follow the steps below and refer to
figure 4-13 and 4-14.
1. Remove the switch cover ASSY by lifting the left side up, while releasing the latches.
Switch cover ASSY
Figure 4-13 Removing the switch cover ASSY
Satellite M30 Maintenance Manual (960-455)
4-29
721699638.002.png 721699638.003.png
4 Replacement Procedures
4.10 Switch cover ASSY/Switch membrane
2. Pull up the insulator .
3. Disconnect the switch membrane cable from the connector PJ7001 on the system
board.
4. Remove the following screws fixing the switch membrane .
• M2.5×4B FLAT HEAD screw ×2
5. Remove the switch membrane by lifting up the left side of the switch membrane.
M2.5×4B FLAT HEAD
PJ7001
Switch membrane
Insulator
Figure 4-14 Removing the switch membrane
4-30
Satellite M30 Maintenance Manual (960-455)
721699638.004.png 721699638.005.png 721699638.006.png 721699638.007.png 721699638.008.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin