WM_03.pdf

DRIVELINE/AXLE

GENERAL PROCEDURES . . . 03-10

FRONT AXLE . . . . . . . . . . . . . . 03-11

REAR AXLE . . . . . . . . . . . . . . . 03-12

DRIVE SHAFT. . . . . . . . . . . . . . 03-13

TECHNICAL DATA . . . . . . . . . . 03-50

SERVICE TOOLS . . . . . . . . . . . 03-60

03–10 GENERAL PROCEDURES

GENERAL PROCEDURES (FRONT

AND REAR AXLES) . . . . . . . . . . . . . . . 03–10–1

End of Toc

GENERAL PROCEDURES (FRONT AND REAR AXLES)

DPE031000000W01

Wheel and Tire Installation

1. When installing the wheels and tires, tighten the wheel nuts in a criss-cross pattern to the following tightening

torque.

Tightening torque

88.2—117.6 N·m {9.00—11.99 kgf·m, 65.06—86.73 ft·lbf}

Connector Disconnection

1. Disconnect the negative battery cable before performing any work that requires handling of connectors. (See

01–17A–1 BATTERY REMOVAL/INSTALLATION [L8, LF].) (See 01–17B–1 BATTERY REMOVAL/

INSTALLATION [MZR-CD (RF Turbo)].)

Suspension Links Removal/Installation

1. For the joint sections with rubber bushings, raise the vehicle using a lift, and then temporarily tighten the

installation bolts and nuts. Lower the vehicle to the ground and tighten them completely with the specified

torque.

End Of Sie

03–10–1

SECTION

To c o f S C T

FRONT AXLE

03–11 FRONT AXLE

FRONT AXLE LOCATION INDEX. . . . . . 03–11–1

FRONT WHEEL HUB BOLT

REPLACEMENT . . . . . . . . . . . . . . . . . . 03–11–1

WHEEL HUB, STEERING KNUCKLE

INSPECTION . . . . . . . . . . . . . . . . . . . . . 03–11–2

WHEEL HUB, STEERING KNUCKLE REMOVAL/

INSTALLATION. . . . . . . . . . . . . . . . . . . . 03–11–2

End of Toc

FRONT AXLE LOCATION INDEX

DPE031104000W01

B3E0311W001

1 Wheel hub, steering knuckle

(See 03–11–2 WHEEL HUB, STEERING

KNUCKLE INSPECTION.)

(See 03–11–1 FRONT WHEEL HUB BOLT

REPLACEMENT.)

(See 03–11–2 WHEEL HUB, STEERING

KNUCKLE REMOVAL/INSTALLATION.)

End Of Sie

FRONT WHEEL HUB BOLT REPLACEMENT

DPE031104000W02

1. Remove the brake calliper component and disc plate.

2. Remove the wheel hub bolt using the SST as

shown in the figure.

3. Place a new wheel hub bolt in the wheel hub.

49 T028 3A0

D3U312ZSI001

03–11–1

FRONT AXLE

4. Install the wheel hub by placing a proper sized

washer on the hub, and tightening the nut as

shown in the figure.

End Of Sie

HUB BOLT

WHEEL NUT

BRASS BAR

WASHER

CHU0311W005

WHEEL HUB, STEERING KNUCKLE INSPECTION

DPE031104060W01

Wheel Bearing Excessive Play Inspection

1. Install the magnetic base and dial gauge as

shown in the figure and measure the wheel

bearing axial excessive play.

• If it exceeds the maximum specification,

replace the wheel hub bearing.

Maximum wheel bearing play

0.05 mm {0.002 in}

End Of Sie

B3E0311W002

WHEEL HUB, STEERING KNUCKLE REMOVAL/INSTALLATION

DPE031104060W02

Caution

• Performing the following procedures without first removing the ABS wheel-speed sensor may

possibly cause an open circuit in the wiring harness if it is pulled by mistake. Before performing

the following procedures, disconnect the ABS wheel-speed sensor connector (axle side) and fix

the wiring harness to an appropriate place where it will not be pulled by mistake while servicing

the vehicle.

1. Remove in the order indicated in the table.

2. Install in the reverse order of removal.

3. After installation, inspect the front wheel alignment and adjust it if necessary. (See 02–11–2 FRONT WHEEL

ALIGNMENT.)

03–11–2

FRONT AXLE

SST

4 6 N•m

{41 61 kgf•cm,

36 53 in•lbf}

SST

42.3 60.1

{4.32 6.12,

31.2 44.3}

SST

37.2 50.4

{3.80 5.13,

27.3 37.1}

SST

53.9 73.5

{5.50 7.49,

39.8 54.2}

43.1 58.8

{4.40 5.99,

31.8 43.3}

SST

78.5 102

{8.01 10.4,

57.9 75.2}

7 10 N•m

{72 101 kgf•cm,

62 88 in•lbf}

235.2 274.4

{23.99 27.98,

173.5 202.3}

N•m {kgf•m, ft•Ibf}

DPE311ZW1001

1 ABS wheel-speed sensor connector

2 ABS wheel-speed sensor

3 Locknut

(See 03–11–7 Locknut Installation Note.)

4 Brake caliper component

(See 03–11–4 Brake Caliper Removal Note.)

5 Disc plate

(See 04–11–19 FRONT BRAKE (DISC) REMOVAL/

INSTALLATION.)

6 Dust cover (European (L.H.D., UK) specs.)

7 Tie-rod end ball joint

(See 02–13–11 FRONT CROSSMEMBER

REMOVAL/INSTALLATION.)

8 Front lower arm ball joint

9 Stabilizer control link upper nut

10 Wheel hub, steering knuckle component

(See 03–11–4 Wheel Hub, Steering Knuckle

Component Removal Note.)

11 Wheel hub component

(See 03–11–4 Wheel Hub Component Removal

Note.)

(See 03–11–6 Wheel Hub Component Installation

Note.)

12 Retaining clip

13 Wheel bearing

(See 03–11–5 Wheel Bearing Removal Note.)

(See 03–11–6 Wheel Bearing Installation Note.)

14 Steering knuckle

15 Hub bolt

(See 03–11–5 Wheel Hub Bolt Removal Note.)

(See 03–11–6 Wheel Hub Bolt Installation Note.)

03–11–3

FRONT AXLE

Locknut Removal Note

1. Knock the crimped portion of the locknut outward

using a small chisel and a hummer.

2. Lock the hub by applying the brakes.

3. Remove the locknut.

A6E6321W001

Brake Caliper Removal Note

1. Remove the brake caliper component from the

steering knuckle and suspend it out of the way

using a cable.

B3E0311W004

Wheel Hub, Steering Knuckle Component Removal Not e

1. Separate the shock absorber from the wheel hub,

steering knuckle component by tapping the upper

part of the steering knuckle with a hammer.

B3E0311W500

Wheel Hub Component Removal Note

1. Remove the wheel hub component using the

SSTs .

49 G033 102

49 G033 105

49 F026 103

CPJ311ZWB004

03–11–4

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: