acc.pdf

(49 KB) Pobierz
ACCELERATOR CONTROL SYSTEM
B ENGINE
SECTION ACC ACC
ACCELERATOR CONTROL SYSTEM
C
D
E
CONTENTS
F
PRECAUTIONS ......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 2
ACCELERATOR CONTROL SYSTEM ...................... 3
Removal and Installation ......................................... 3
REMOVAL ............................................................ 3
INSTALLATION .................................................... 3
INSPECTION AFTER INSTALLATION ................. 3
G
H
I
J
K
L
M
ACC-1
Revision: 2005 March
2005 X-Trail
897336071.013.png 897336071.014.png 897336071.015.png 897336071.016.png
 
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ABS00DCY
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
ACC-2
Revision: 2005 March
2005 X-Trail
897336071.001.png
 
ACCELERATOR CONTROL SYSTEM
ACCELERATOR CONTROL SYSTEM
PFP:18005
A
Removal and Installation
ABS00D0V
ACC
C
D
E
F
G
PBIC2731E
1.
Accelerator pedal assembly
H
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector.
2. Loosen nuts, and remove accelerator pedal assembly.
CAUTION:
Do not disassemble accelerator pedal assembly. Do not remove accelerator pedal position sen-
sor from accelerator pedal assembly.
Avoid impact from dropping etc. during handling.
Be careful to keep accelerator pedal assembly away from water.
Do not adjust adjusting screw (painted yellow).
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER INSTALLATION
CAUTION:
When the harness connector of the accelerator pedal position sensor is disconnected, perform
“Accelerator Pedal Released Position Learning”. Refer to EC-88, "Accelerator Pedal Released Position
Learning" .
I
J
K
L
M
Make sure that accelerator pedal moves smoothly within the whole operation range.
Make sure that accelerator pedal securely returns to the original position.
For the electrical inspection of accelerator pedal position sensor, refer to EC-555, "DTC P2122, P2123
APP SENSOR" , EC-562, "DTC P2127, P2128 APP SENSOR" and EC-578, "DTC P2138 APP SEN-
SOR" .
ACC-3
Revision: 2005 March
2005 X-Trail
897336071.002.png 897336071.003.png 897336071.004.png 897336071.005.png 897336071.006.png 897336071.007.png 897336071.008.png 897336071.009.png 897336071.010.png 897336071.011.png
 
ACCELERATOR CONTROL SYSTEM
ACC-4
Revision: 2005 March
2005 X-Trail
897336071.012.png
 

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin