Colt Peacemaker 22.pdf

COLT'S

Peacemaker .22 Caliber

RIVOLVIR

Loading. Firing. CorrectCare

COLT'S

Peacemaker .22 Caliber

Single Action Revolver

(

FIRING

CORRECT

CARE

SAFETY

POSITION

GENERAL. Your Colt Single Action Peacemaker

is one of the most simple, rugged and dependable

handguns ever manufactured. Used correctly

it will serve you indefinitely without ever re-

quiring major repairs. Before handling or shoot-

ing your Single Action, BE SURE to read this

sheet and carefully note the precautions listed.

These precautions, though important, are sim-

ple, and correct handling will quickly become

automatic with you. The precautions apply to

EVERY single action revolver and are dictated

by the inherent

HALF-COCK

FULL-

COCK

mechanical

structure

of ALL

handguns

of this type.

ACTION. "Single Action" means that the ham-

mer of this revolver ry1ust be drawn back-or

"cocked" -with the thumb, before each shot is

fired. When cocking the Single Action, you will

notice that there are three distinct hammer posi-

tions as follows:

3. FULL-COCK-with the hammer all the

way back and the revolver ready to fire.

IMPORTANT-The Safety and Half-Cock

notches are designed to prevent the trigger

from being pulled, so Do NOT try to force

the trigger with the hammer in either of

these two positions. If it is desired to lower

the hammer, pull the hammer baok slightly;

then pull the trigger and lower the ham-

mer carefully.

1. SAFETY POSITION-with the hammer

held safely away from the firing pin.

2. HALF-COCK-with the hammer approx-

imately half way back and the cylinder

bolt depressed,

leaving the cylinder free

to rotate.

.""

""'-.....

LOADING. Draw the hammer back to the Half-Cock

position. Do not touch the triKger but leave it free to

snap into the notch. (NOTE: If the hammer should be

at the Full-Cock position, lower it all the way first and

then draw back to Half-Cock. Otherwise, the bolt earn

lever cannot operate to release the cylinder.) This will

leave the cylinder free to rotate for 10adinK. Open the

LoadinK Gate on the'right-hand side of the revolver and

load each chamber. Close the loading gate.

UNLOADING. After firinJ.:, draw the hammer back to

Half-Cock position, open the gate and operate t.he ejector

lever <located under the barrel)

to eject the empty

cartridges in the chamber and, the hammer on the empty

sixth chamber.

IMPORTANT - When placing the hammer in the Safety

position, first lower it all the way gently (since dropping

the hammer hard can fire the cartridge) and then

draw it back to the Safety position. If the hammer is

incorrectly lowered, direct from the Half- or Full-Cock

positions to the Safety position, the sear may not

engage the hammer notch completely and safely.

REMOVING THE CYLINDER. To remove the cylinder for

cleaning, inspection or exchange (dual cylinder model):

1. BE SURE the hammer is in the Half-Cock position

with the cylinder

cartridJ.:e cases.

SAFE POSITION-CARRYING. The safest way to carry

your Colt SinJ.:le Action

free to rotate (see Note under

paragraph

on Loading).

Make sure the Loading

Peacemaker

is with five

Gate is open.

WHEN ORDERING PARTS, SPECIFY: Model, Caliber, Serial Number, and Name of Part.

CALIBER: .22 Short, Long, Long Rifle

.22 Winchester

Magnum Rimfire

1 Backstrap . . . . . . . . . . . . . . . . . .51758

2 Backstrap Screw-Bottom-(2). . . . . . .51742

3 Backstrap Screw- Top-(2). .. .. . ... .51743

4 Backstrap Screw-Front. .. . . . . . ... .. .51743

5 Barrel-4X"-.22 Caliber .52819

6 Base Pin .52811

7 Base Pin Lock Screw. . . . . . . . . . . . . . . .52804

8 Base Pin Lock Nut .52803

9 Base Pin Lock Spring. . . . . .. . . . ... .. .51717

10 Bolt 52810

11 Bolt Spring Screw.. . .. .51746

12 Bolt and Trigger Screw. . . . . . . . ... .. .51745

13 Bolt and Trigger Spring .51750

14 Cylinder-.22 Long Rifle. . . .. . . . . . . .. .52817

14 Cylinder-.22

Magnum

.52823

28 Hand Spring. . .. . . . . . ... . . . . . .. . . . . ..52825

29 Main Spring.. .. . .51718

30 Recoil Cup. . . . . . . .. . . .. . .. . . . . . . . .. .52809

31 Recoil Cup Pin

.52807

16 Ejector Rod Tube .52808

17 Ejector Spring. . . . . . .. . . . . . . .. . . . . . . .51722

18 Ejector Tube Screw .51742

19 Firing Pin. . . . . . . .. .. . .. . .. . . . . . . .. . . .51744

20 Firing Pin Spring ..51717

21 Frame . . . . . ... . .. . . . . . .. ..52822

22 Gate ..51720

23 Gate Detent. . . . . . . . .. . . . .., . . . .. . . . .52816

24 Gate Detent Spring. . . . . . . . . . . . ... . . .50156

25 Hammer .52812

26 Hammer Screw. . . . . . .. . . . . . .. . . . .. .. 51747

27 Hand and Post Assembly

"""''''''''''''''''''

..95003

32 Stock-Left

Hand. . . . . . . .. . . . . . ... .51797-1

.51797-2

34 Stock Pin .51719

35 Stock Screw. . . . . . . .. . .. . . . .. .. . . . .. .50088

36 Stock Screw Nut.

Hand..

"""""""

.50089

'"''''''''''''''''

37 Trigger

51728

38 Washer-Small-(8)

.51751

39 Washer-Large-(1)

.51752

.52815

2. Depress the base pin catch.

3. Remove the base pin. The cylinder can now be

removed from the Loading Gate side of the revolver

without danger of scratching or other damage.

TO REINSERT CYLINDER, or INSERT EX-

CHANGE CYLINDER: use reverse procedure of

above, making sure that hammer is in the half-cock

position.

CLEANING THE SINGLE ACTION PEACEMAKER.

Using modern, factory-loaded cartridges with smokeless

powder and non-corrosive primers, all you need to keep

your Colt Revolver in perfect condition is a brass wire-

bristle brush; a brass, aluminum or hardwood cleaning

rod (do not use steel since this can damage the rifling at

the muzzle) with "jag" type tip; cotton flannel patches

cut to fit the bore snugly; a good cleaning solution (there

are several preparations on the market); and a light, non-

gumming oil. Remove the cylinder (see directions above).

Dip the brass wire brush in the cleaning solution and

scrub out the barrel bore and cylinder chambers well.

(Never try to reverse direction while running the wire

brush through the bore; pass it all the way through and

then pull it back.) Wipe out barrel and cylinder with

flannel patches until the last patch comes out clean.

Finally, give the bore, chambers, and all parts a good

(but not excessive) coat of oil. Making sure that the

hammer is in the Half-Cock position and the Loading

Gate is open, replace the cylinder in the revolver.

VTARNING

DO NOT "FAN"

YOUR COLT REVOLVER

TO PERMIT "FANNING," THE INTERNAL

MECHANISM OF ANY SINGLE ACTION

REVOLVER MUST BE SPECIALLY ALTERED.

THIS ALTERATION WILL DEFINITEL Y REN-

DER YOUR REVOLVER BOTH UNSAFE AND

UNSATISFACTORY FOR GENERAL, ALL-

AROUND SHOOTING AND IS NOT RECOM-

MENDED.

15 Ejector Rod.

33 Stock-Right

YOUR

eOl T'5

WAIRIRAN~lrY

All Colt.', Revolvers and Automatic Pistols

or. built to exacting standards of engineer-

ing and manufacturing and ore rigidly in-

spected before leaving our factory. They ore

warranted to b. fr.. from defects in materiol

and workmanship under normal use and

service for a period of 12 manit" from the

date of purchase. Colt', obligation is limited

to repairing 'or replacingf F.O.B. Hartford,

Conn., U.S.A., any port of a Colt's Revolver

or Automatic Pistol which Colt', examination

disci os., to b. thus defective.

This warranty

is in lieu of alf other warren.

ties, ex.pressed

or implied.

This warranty

shall not apply

to defects

resulting

from

accidents,

olterations

or misuse.

If-in

the

opinion

of Colt',

gunsmiths

employed

Hartfard, Cannecticut""'='"1odifications, changes

or additions made outside our factory have

affected the operation of the weapon to ren.

der it faulty, this warronty shall be void. This

warranty shall also be void if any part not of

Colt's manufacture

has been incorporated,

if other than factory loaded ammunition

fired in it.

@ Cort Industries

Firearms

Marketi~g Division

150 Huyshope Avenue

Hartford, Conn., U.S.A. 06102

FORM PM-IOOO 1/72

PRINTED IN U.S.A.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: