torebka - Dotted Dream - opis wykonania.pdf - Torebki(1) - solderpad

Dotted Dream

purse

width 30 cm, height 22 cm

MATERIALS

- 40 cm floral and 10 cm polka-dot printed fabric for exterior

- 55 cm striped fabric for lining

- 40 cm interfacing, Vlieseline G 700, width 90 cm

- 100 cm velvet ribbon, width 10 mm

- sew-on snap fastener, ø 14 mm

(- 7 cm x 27 cm piece of stiff cardboard)

Suitable materials for the purse are: velvet (velveteen), corduroy, denim

or tightly-woven cotton fabric.

ABOUT PATTERN

Print out the pattern sheets, cut the pattern pieces out and join them as

indicated by the small-scale pattern pieces. Add 1 cm seam allowances to

all edges when cutting out the purse pieces from the fabrics.

CUTTING

Cut purse lining (1) from striped fabric. Cut up pattern for purse lining

into two pattern pieces: upper part of purse (1A) and lower part of purse

(1B). Cut upper parts of purse and handles from polka-dot fabric and

lower part of purse from floral fabric as indicated on list of pattern pieces.

SEWING

Seams and hems: Stitch seams with straight stitch and topstitch them

close to edge. No seam finish is necessary as the purse is fully lined.

Interfacing: Cut interfacings for handles and for all purse exterior pieces

and fuse them in place. Do not add seam allowances to interfacings for

handles.

Handles: Fold handle piece in half, right sides together, and stitch its long

edges together. Press seam open and turn handle right side out. Press

handle flat, placing seam in the middle of handle. Fold handle in half again,

with pressed edges together and seam inside folded handle, and stitch

edges of handle together between pattern markings.

Joining: Pin and stitch upper parts of purse to lower part, right sides

together. Fold seam allowances toward upper parts and topstitch seams.

Cut pieces of velvet ribbon for trims along seams joining upper and lower

parts of purse. Measure required lengths of ribbon on pattern piece and

add seam allowances. Pin ribbons along seams, placing them on upper

parts of purse, and stitch them in place along both edges.

Cut 4 cm and 10 cm pieces from velvet ribbon. Stitch ends of longer piece

of ribbon together and fold ribbon to form bow. Wrap shorter piece of

ribbon around bow to form center of bow and stitch to secure it. Cut

20 cm piece from velvet ribbon and stitch it at its midpoint over seam

joining upper and lower part of purse, right sides together. Fold each half

of ribbon so that right side is facing out. Stitch bow on top of ribbon.

Pin and stitch side seams of purse exterior, right sides together. Stitch

seams at bottom corners, right sides together. Machine-baste ends of each

handle to top edge of purse, right sides together, as marked on pattern.

Stitch side seams of purse lining; leave 10 cm opening in one side seam

for turning purse right side out. Stitch seams at bottom corners of lining.

Press side seams of both purse exterior and lining open.

PATTERN PIECES

1 purse lining

1 ✄

upper part of purse A

Joining purse exterior and lining: Insert purse exterior and lining

within one another, right sides together and with handles in between.

Stitch top edge of purse. Turn purse right side out. Press and topstitch its

top edge.

1 ✄

lower part of purse B

2 handle

This design and pattern is protected under the Copyright Act.

No material may be reproduced in part or in whole. All commercial

and industrial use is strictly prohibited.

If you wish you can insert a piece of cardboard at the bottom of the purse

between the exterior and lining. Close opening for turning on lining. Sew

on snap fastener as marked on pattern.

Dotted Dream I

taite- vouw- Stoffbruch- fold- vikning -pliure

Dotted Dream II

TARKISTUSRUUTU

KONTROLLRUTA

CONTROLEVELD

CONTROL SQUARE

KONTROLLFELD

5 cm x 5 cm

taite- vouw- Stoffbruch- fold- vikning -pliure

torebka - Dotted Dream - opis wykonania.pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: