barbecue trolley-wozek do grilla.pdf

NAFI |

Barbecue Trolley

Many of those odd bits and pieces

required at the outdoor barbecue

can be delivered conveniently on

this barbecue (or indoor tea)

trolley. Basic design consists of two

equal sized flat trays supported on

corner posts. However we strongly

advise that you decide first on the

sort of wheel/axle system since

width of trays should be made to fit

closely between the wheels. With

some changes in details the width

of this barbecue trolley can be

adjusted to suit your purchased

wheel, axle, bracket units. As an alternative you could use a system

of bolts and lock nuts, etc to fasten wheels to base tray or corner post

as shown later.

TOOLS YOU WILL NEED

MATERIALS YOU WILL NEED

Drill and bit,

countersunk bit

Timber

Hardware

Note that this trolley is designed

on the assumption that it will be

generally protected from

exposure to rain and dew. If

this limit on exposure is

accepted then standard door

jamb lining can be used (e.g.

from Pacific Maple, meranti,

oregon, radiata pine, Tasmanian

oak, etc.) and standard or

interior quality particle board or

plywood would be acceptable

for bottom of trays. Corner of

posts could be timber selected

for appearance rather than for

performance under weather

exposed conditions.

8/50 x 6 mm

diameter round

head wood

screws (end rail

to post).

Measuring tape/

rule

Carpenter's square

and pencil

Adjustable spanner

40 mm x 6 mm

diameter round

head wood

screws (side rail

to post, handle)

Wood chisel

Hammer

Screwdriver

Chisel

100/50 x 2.8

mm bullet head

nails. (bottom

planks)

PVA wood

adhesive

2/150 mm

diameter

wheeels/axles

bracket units as

available.

50 mm x 50 mm DAR

file:///C|/Documents and Settings/colin cave/My Documents/woodworking plans/outside/garden equipment/NAFI.htm (1 of 5)19/03/2005 08:10:11

Saws

NAFI |

4 pieces 750 mm * (4

posts)

100 x 38 mm door jamb

lining (see diagram)

4 pieces 900 mm * (side

rails)

4 pieces 600 mm * (end

rails)

100 x 25 mm DAR

softwood

16 pieces as bottom

planks or use 19 mm

particleboard or

12 mm plywood cut to fit

frames.

75 x 25 mm DAR softwood

1 piece 900 mm * (rail

bracket)

19 mm or 25 mm

diameter dowel or

1 piece 700 mm for

handle/rail

* Discuss these length

requirements with your

supplier, who will supply

standard lengths of

timber from which these

pieces can be cut.

Step by Step

Cut corner posts

From the pieces of 50 x 50 mm DAR timber cut four posts (P) each 750 mm long.

Cut end rails

From the pieces of door jamb cut four end rails (A) each of an exact length to suit the

axle/wheel system.

Example: For an overall width of tray of 500 mm cut four end rails each 465 mm long

Mark out side rails

At each end of the four side rail pieces mark out as

shown 80 mm from each end. Mark edges as guide for

removal of excess material.

Saw and chisel out rail section

Saw and cut on marked line 80 mm from each end and

chisel out excess materials to give four rails as indicated in

file:///C|/Documents and Settings/colin cave/My Documents/woodworking plans/outside/garden equipment/NAFI.htm (2 of 5)19/03/2005 08:10:11

NAFI |

diagram. Check the dimension shown as 740 mm in

diagram. This measurement should be the same for each

cut and trimmed rail.

Assemble tray frame

Fit tray rails together and fix in position using

nails. Check squareness of trays and confirm

that the two trays are the same size. Trim

rails and adjust where necessary.

Cut bottom planks

Measure internal width of tray as shown in previous diagram. Cut 16 bottom planks to

this length or cut particleboard or plywood to fit in as tray bottom.

Square up trays

Fit a bottom into each tray and fix

in place using glue and nails.

Before final fixing square up tray

and check that the two trays are of

the same size.

Attach legs

Fix trays to the four legs as shown

in diagram below using glue and

screws. Note that the final length

of each pair of legs will depend on

wheel/axle bracket system used.

However, in this initial assembly,

the four posts are of equal length

such that the overall height

remains at 750 mm. The distance

between trays maybe varied

depending on the wheel and axle

system chosen.

Fix wheel system

Note: The assembly could stand on

four legs until the wheels are

attached to the front of the units,

or the front 'legs' are removed first as appropriate for selected wheel assembly. Fit

selected wheel/axle system. Cut off excess front legs as required.

Provide drainage holes

If sheet products (particleboard or plywood) are used in trays, provide drainage holes

(9mm 3/8" diameter in each corner. Loose fitted plank bottom if used should give

adequate drainage.

Smooth and rounding off

Using sanding disc, sander or hand sanding or planing, smooth and round off all

accessible sharp corners and edges of the trays and posts. Punch all nails if desired and

file:///C|/Documents and Settings/colin cave/My Documents/woodworking plans/outside/garden equipment/NAFI.htm (3 of 5)19/03/2005 08:10:11

NAFI |

fill nail holes with putty/filler the same colour as timber.

Note: The trays could have side rails projecting 5-10 mm beyond posts. These

projections should be rounded off thoroughtly, or trimmed off.

Cut, trim and fix handle

< From the piece of 75 x 25 mm DAR x 900

mm cut two handles each 450 mm long. Trim

or shape as in diagram, smooth all corners

and edges, then screw - and glue-fix to rear

end of upper tray as in diagram.

Note: To make sure that handle fits flat to the

rail you may need to chisel out small pieces of

the handle where it comes into contact with

the heads of screws into posts or use

countersunk screws.

Cut to length and insert broom handle/dowel.

Use glue in hole and drive in one 30 mm long

nail through top edge of shaped timber piece

into handle/dowel.

Apply finishes

Clear finish with three coats of satin clear polyurethane finish, or selected stains, or

garden furniture finish or conventional paint finish. It is strongly recommended that the

trolley receive a thorough coating of one of these finishes and that this coating be

maintained adequately.

For weather exposed trolleys

If the trolley is to be exposed to weather for long periods, then be selective about

materials. For timber components for example select 'durable' or moderately durable

timbers such as western red cedar, jarrah, black butt etc. or preservative treated

timber, OR pay particular attention to applying exterior finishes (and then maintenance)

to low durability timbers. Fastenings (nails, bolts, etc.) should be non-corroding such as

hot dipped or electroplated galvanised coatings.

file:///C|/Documents and Settings/colin cave/My Documents/woodworking plans/outside/garden equipment/NAFI.htm (4 of 5)19/03/2005 08:10:11

NAFI |

Tips Index

Timber Talk with Harry & Sal

Disclaimer : While the Timber and Building Materials Association (NSW) Limited (TABMA) and its

members believe this publication is an invaluable guide to this project, the Association cannot guarantee

that every statement is without flaw. Therefore, the Association and its members hereby disclaim all

liability for error or omissions of any kind, whether they be negligent of otherwise, or for any loss,

damage or other consequence which may arise from any person relying on information stated in this

publication.

This document was prepared with the assistance and co-operation of the Timber Development Association

NSW Ltd.

For further advice telephone the TDA Timber Industry Advisory Service on (02) 360 3088.

Site development by Internet Solutions Australia , Canberra - Graphic design by Swell Design Group , Canberra

file:///C|/Documents and Settings/colin cave/My Documents/woodworking plans/outside/garden equipment/NAFI.htm (5 of 5)19/03/2005 08:10:11

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: