Dzwonki na choinkę.pdf

(666 KB) Pobierz
Bell_Ornamentpg2
Christmas Bell Ornament
page 1 of 5
© FamilyFun
FamilyFun.com
296766267.034.png 296766267.035.png 296766267.036.png 296766267.037.png 296766267.001.png 296766267.002.png 296766267.003.png 296766267.004.png 296766267.005.png 296766267.006.png
Christmas Bell Ornament
page 2 of 5
© FamilyFun
FamilyFun.com
296766267.007.png 296766267.008.png 296766267.009.png 296766267.010.png 296766267.011.png 296766267.012.png 296766267.013.png 296766267.014.png
Christmas Bell Ornament Directions
page 3 of 5
Step 1: Print out all 5 pages of the bell ornament.
Step 2: Fold each bell along the center dashed line and cut out the
bell along the outer dashed grey line. Do this for all 4 bells. Then cut
out both of the round clappers.
Christmas Bell Ornament
page 1 of 4
Christmas Bell Ornament
page 1 of 4
Christmas Bell Ornament
page 1 of 4
page 1 of 5
© FamilyFun
FamilyFun.com
© FamilyFun
FamilyFun.com
© FamilyFun
FamilyFun.com
© FamilyFun
FamilyFun.com
Step 4: Unfold one bell and place it (picture side down) on a
table or at surface. Cover the left folded side with glue.
Step 5: Cut a thin piece of ribbon or string about 14 inches long.
Place the ribbon or sting onto the glued surface as close to the
middle as possible. Place it so that about an inch and a half sticks
out at the bottom of the bell and the rest sticks out of the top.
© FamilyFun
FamilyFun.com
296766267.015.png 296766267.016.png 296766267.017.png 296766267.018.png 296766267.019.png 296766267.020.png 296766267.021.png 296766267.022.png 296766267.023.png 296766267.024.png
Christmas Bell Ornament Directions
page 4 of 5
Step 6: Place another bell (picture side up), onto the bell with the
glue and string. Make sure the edges line up, then push down to
stick the bells together with the string between them. Fold back
the 2 aps that are not glued together.
Step 7: Place another bell (picture side down) on a table or at surface.
Spread glue onto the right half of the bell. Next, place the long half of
the ribbon or string onto the glued surface as close to the middle as
possible, this should create a loop between the bells.
Step 8: Place the fourth bell (picture side up) onto the bell with
the glue. Press down so that the ribbon sticks between those 2
bells. Fold back the aps that are not glued together.
Step 9: Spread glue over the remaining blank sides of the bells. Then
bring the bells together so that the edges match up. Press rmly so
the bell stays together.
© FamilyFun
FamilyFun.com
296766267.025.png 296766267.026.png 296766267.027.png 296766267.028.png 296766267.029.png 296766267.030.png 296766267.031.png 296766267.032.png
Christmas Bell Ornament Directions
page 5 of 5
Step 10: Place the clapper (picture side down) on a table or at
surface. Spread glue on the blank side, then press the ribbon
that is sticking out of the bottom of the bell into the glue. Last,
place the second clapper (picture side up) on top of the other
clapper. Your ornament is nished!
© FamilyFun
FamilyFun.com
296766267.033.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin